komatsu pc210lci 11e0 hydraulic excavator operation and maintenance manual uenam01710 1

komatsu pc210lci 11e0 hydraulic excavator operation and maintenance manual uenam01710 2

komatsu pc210lci 11e0 hydraulic excavator operation and maintenance manual uenam01710 3

komatsu pc210lci 11e0 hydraulic excavator operation and maintenance manual uenam01710 4

komatsu pc210lci 11e0 hydraulic excavator operation and maintenance manual uenam01710 5

Komatsu PC210LCi-11E0 Hydraulic Excavator Operation and Maintenance Manual UENAM01710

$20.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: UENAM01710
Format: PDF
Size: 124.2MB
Number of Pages: 504

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- PC210LCi-11E0 Hydraulic Excavator

1. FOREWORD
1.1. CONTENTS
1.2. READ THIS MANUAL
1.3. KOMATSU MACHINE OPERATOR PRIVACY POLICY
1.4. SAFETY INFORMATION
1.5. INTRODUCTION
1.5.1. intelligent Machine Control
1.5.2. MAIN USE OF MACHINE
1.5.3. DEMOLITION WORK
1.6. ABBREVIATION LIST
1.7. DECLARATION OF CONFORMITY
2. SAFETY
2.1. SAFETY LABELS
2.1.1. LOCATION OF SAFETY LABELS
2.1.2. SAFETY LABELS
2.2. PRECAUTIONS FOR OPERATION
2.2.1. START ENGINE
2.2.2. PRECAUTIONS RELATED TO CONTROL BOX
2.2.3. PRECAUTIONS RELATED TO SEMIAUTO MODE
2.2.4. PRECAUTIONS FOR TRANSPORTATION
3. OPERATION
3.1. GENERAL VIEW
3.1.1. MACHINE EQUIPMENT NAME
3.1.2. CAB EQUIPMENT NAMES
3.2. EXPLANATION OF COMPONENTS
3.2.1. EXPLANATION OF MACHINE MONITOR EQUIPMENT
3.2.2. SWITCH
3.2.3. CONTROL LEVERS AND PEDALS
3.2.4. intelligent Machine Control SYSTEM
3.2.5. OTHER EQUIPMENT
3.3. MACHINE OPERATIONS AND CONTROLS
3.3.1. CHECKS AND ADJUSTMENT BEFORE STARTING ENGINE
3.3.2. START ENGINE
3.3.3. HANDLING QUICK COUPLER PIN GRAB
3.3.4. METHOD FOR STOPPING ENGINE
3.3.5. PROHIBITED OPERATIONS
3.3.6. PARK MACHINE
3.4. HANDLING RADIO
3.5. TRANSPORTATION
3.5.1. REMOVE AND INSTALL GNSS ANTENNA
3.5.2. REMOVE AND INSTALL HANDRAIL
3.5.3. REMOVE AND INSTALL GNSS ANTENNA AND ANTENNA FOR NETWORK MODEM
3.6. PRECAUTIONS FOR LONGTERM STORAGE
3.6.1. STARTING MACHINE AFTER LONGTERM STORAGE
3.7. TROUBLES AND ACTIONS
3.7.1. IF ERROR INFORMATION IS DISPLAYED ON CONTROL BOX
3.7.2. OTHER TROUBLE
4. MAINTENANCE
4.1. MAINTENANCE SCHEDULE
4.1.1. MAINTENANCE SCHEDULE TABLE
4.2. MAINTENANCE PROCEDURE
4.2.1. EVERY 500 HOURS MAINTENANCE
5. SPECIFICATIONS
5.1. SPECIFICATIONS
5.1.1. SPECIFICATIONSPC210LCI11E0
6. ATTACHMENTS AND OPTIONS
6.1. PRECAUTIONS FOR USING ATTACHMENT AND OPTIONS
6.1.1. PRECAUTIONS WHEN SELECTING
6.1.2. READ THE OPERATION AND MAINTENANCE MANUAL THOROUGHLY
6.1.3. PRECAUTIONS WHEN REMOVING AND INSTALLING
6.1.4. PRECAUTIONS FOR USING
6.2. ATTACHMENTS AND OPTIONS
6.2.1. AUTO TILT BUCKET
6.3. RECOMMENDED ATTACHMENT OPERATIONS
6.3.1. HYDRAULIC BREAKER
7. SETTING
7.1. INTELLIGENT MACHINE CONTROL SETTINGS
7.2. CONTROL BOX
7.2.1. METHOD FOR DISPLAYING MAIN MENU
7.3. MACHINE MONITOR
7.3.1. MACHINE SETTINGS
7.3.2. MC SETTING
8. EXECUTIONS
8.1. SEMIAUTO MODE
8.1.1. PRECAUTIONS FOR OPERATION
8.1.2. PRECAUTIONS FOR REPLACING PARTS AND FAILURES
8.1.3. WORKING MODE
8.1.4. WORKING MODE (WHEN AUTO TILT BUCKET IS EQUIPPED)
8.1.5. SEMIAUTO MODE SETTINGS
8.2. TRAVEL MODE
8.2.1. TRAVEL MODE SETTINGS
8.2.2. DISPLAY OF TRAVEL MODE
8.2.3. OFFSET MENU OF SURFACE
8.2.4. TARGET SURFACE SETTINGS
8.3. ROUGH DIGGING MODE
8.3.1. METHOD FOR SETTING ROUGH DIGGING SCREEN
8.3.2. TEMPORARY DESIGN MENU
8.4. FINE DIGGING MODE
8.4.1. METHOD FOR SETTING FINE DIGGING MODE SCREEN
8.5. TARGET SURFACE SETTINGS
8.5.1. TARGET SURFACE SETTING MENU
8.5.2. METHOD FOR SETTING TARGET SURFACE
8.6. BUCKET EDGE POSITION
8.6.1. DISPLAY BUCKET EDGE POSITION
8.6.2. METHOD FOR COMPARING WITH BENCHMARK
8.6.3. METHOD FOR CORRECTING BUCKET EDGE POSITION
8.7. DAILY CALIBRATION
8.7.1. WALKAROUND CHECKS OF INTELLIGENT MACHINE CONTROL EQUIPMENT
8.8. CHECK GNSS COMMUNICATION STATUS
8.8.1. METHOD FOR CHECKING GNSS COMMUNICATION STATUS
8.8.2. METHOD FOR CHECKING NUMBER OF SATELLITES AND ERROR OF POSITIONING
8.8.3. METHOD FOR DISPLAYING BUCKET EDGE COORDINATES
8.8.4. METHOD FOR SETTING SATELLITE POSITION DISPLAY AND ELEVATION ANGLE
8.8.5. METHOD FOR DISPLAYING GNSS RECEIVER INFORMATION
8.8.6. METHOD FOR CHEKING EXPECTANCY OF EDGE ACCURANCY
8.8.7. METHOD FOR SETTING GLONASS SATELLITE
8.8.8. METHOD FOR SETTING TILT SENSOR
8.9. USE OF TOPO SURVEY
8.9.1. METHOD FOR PERFORMING TOPO SURVEY MANUALLY
8.9.2. METHOD FOR PERFORMING AUTOTOPO SURVEY
8.9.3. METHOD FOR CANCELING TOPOGRAPHIC SURVEYS
8.10. TROUBLESHOOTING
8.10.1. CONTROL BOX SCREEN DISPLAY
8.10.2. SEMIAUTO MODE
8.10.3. WORKING ACCURACY
8.10.4. AUTO TILT BUCKET
9. INDEX

Rate this product