komatsu pc360lc 10 pc360nlc 10 pc360lc 10 demolition base spec pc360nlc 10 demolition base spec hydraulic excavator operation and maintenance manual uenam00863 1

Komatsu PC360LC-10, PC360NLC-10, PC360LC-10 Demolition Base Spec, PC360NLC-10 Demolition Base Spec Hydraulic Excavator Operation and Maintenance Manual UENAM00863

$20.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: UENAM00863
Format: PDF
Size: 33.1MB
Number of Pages: 464

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- PC360LC-10 Demolition Base Spec PC360NLC-10 Demolition Base Spec Hydraulic Excavator
- PC360NLC-10 Demolition Base Spec PC360NLC-10 Demolition Base Spec Hydraulic Excavator
- PC360LC-10 Demolition Base Spec PC360NLC-10 Demolition Base Spec Hydraulic Excavator

1. FOREWORD
1.1. FOREWORD
1.2. SAFETY INFORMATION
1.3. NOISE (PC360LC10, PC360NLC10)
1.4. VIBRATION LEVELS
1.5. INTRODUCTION
1.6. PRODUCT INFORMATION
1.6.1. PRODUCT IDENTIFICATION NUMBER (PIN) / MACHINE SERIAL NO. PLATE
1.6.2. EPA regulations, engine number plate
1.6.3. Service meter location
1.6.4. Your machine serial numbers and distributor
1.6.5. SERIAL PLATE
1.7. DECLARATION OF CONFORMITY
1.8. Contents
2. SAFETY
2.1. Safety
2.2. SAFETY LABELS
2.2.1. LOCATION OF SAFETY LABELS
2.2.2. SAFETY LABELS
2.3. General precautions common to operation and maintenance
2.3.1. Precautions before starting operation
2.3.2. Preparations for safe operation
2.3.3. Fire prevention
2.3.4. Precautions when getting on or off machine
2.3.5. DO NOT GET CAUGHT IN WORK EQUIPMENT
2.3.6. Precautions related to protective structures
2.3.7. Protection against falling, flying, or intruding objects
2.3.8. ACTIONS IN THE EVENT OF DAMAGE TO SAFETY STRUCTURES
2.3.9. UNAUthorized modification
2.3.10. Precautions related to attachments and options
2.3.11. PRECAUTIONS RELATED TO CAB GLASS
2.3.12. PRECAUTIONS WHEN RUNNING ENGINE INSIDE BUILDING
2.4. Precautions for operation
2.4.1. Precautions for jobsite
2.5. SAFETY MACHINE OPERATION
2.5.1. Starting engine
2.5.2. When operating
2.5.3. TRANSPORTATION
2.5.4. Towing
2.5.5. LIFTING OBJECTS WITH BUCKET LINK LIFTING DEVICE (OPTIONAL EQUIPMENT)
2.5.6. SAFETY RULES FOR LIFTING OBJECTS
2.6. Precautions for maintenance
2.6.1. Precautions before starting inspection and maintenance
2.6.2. Precautions for inspection and maintenance
3. OPERATION
3.1. General view
3.1.1. General view of machine
3.1.2. GENERAL VIEW OF CAB
3.1.3. GENERAL VIEW OF CONTROLS AND GAUGES
3.1.4. Machine monitor
3.2. Explanation of components
3.2.1. Machine monitor
3.2.2. Switches
3.2.3. CONTROL LEVERS AND PEDALS
3.2.4. OPENING AND CLOSING ROOF WINDOW
3.2.5. Opening and closing cab front window
3.2.6. EMERGENCY ESCAPE HAMMER
3.2.7. Door lock
3.2.8. OPEN AND CLOSE ENGINE HOOD
3.2.9. HANDLING AIR CONDITIONER
3.2.10. HANDLING RADIO
3.2.11. AUXILIARY ELECTRIC POWER
3.2.12. Fuse
3.2.13. Fusible link
3.2.14. Tool box
3.2.15. Grease pump holder
3.2.16. Fire extinguisher
3.2.17. BATTERY DISCONNECT SWITCH
3.2.18. System operating lamp
3.2.19. HANDLING KDPF
3.2.20. HANDLING KCCV
3.2.21. Handling machines equipped with KOMTRAX
3.3. Machine operations and controls
3.3.1. Checks and adjustment before starting engine
3.3.2. STARTING ENGINE
3.3.3. AMBIENT TEMPERATURE RANGE FOR OPERATION AND STORAGE
3.3.4. OPERATIONS AND CHECKS AFTER STARTING ENGINE
3.3.5. STOPPING ENGINE
3.3.6. MACHINE OPERATION
3.3.7. Steering machine
3.3.8. SWINGING MACHINE
3.3.9. WORK EQUIPMENT CONTROLS AND OPERATIONS
3.3.10. WORKING MODE
3.3.11. Prohibited operations
3.3.12. RULES FOR OPERATION
3.3.13. Travelling on slopes
3.3.14. Escape from mud
3.3.15. RECOMMENDED APPLICATIONS
3.3.16. REPLACING AND INVERTING BUCKET
3.3.17. When parking machine
3.3.18. After daily work completion
3.3.19. LOCKING
3.4. TRANSPORTATION
3.4.1. Transportation procedure
3.4.2. Loading and unloading with trailer
3.4.3. Lift machine
3.5. COLD WEATHER OPERATION
3.5.1. COLD WEATHER OPERATION INFORMATION
3.5.2. AFTER DAILY WORK COMPLETION
3.5.3. AFTER COLD WEATHER SEASON
3.6. Longterm storage
3.6.1. Before storage
3.6.2. During storage
3.6.3. After storage
3.6.4. Starting mAchine after longterm storage
3.7. TROUBLES AND ACTIONS
3.7.1. Running out of fuel
3.7.2. Phenomena that are not failures
3.7.3. TOWING MACHINE
3.7.4. Lightweight towing hole
3.7.5. Severe job condition
3.7.6. DISCHARGED BATTERY
3.7.7. Other trouble
4. MAINTENANCE
4.1. Rules for maintenance
4.1.1. Service Meter Reading
4.1.2. Komatsu Genuine Replacement Parts
4.1.3. Komatsu Genuine Lubricants
4.1.4. Always use clean washer fluid
4.1.5. Fresh and Clean Lubricants
4.1.6. Check drained oil and used filter
4.1.7. Fuel strainer
4.1.8. Welding instructions
4.1.9. Do not drop things inside machine
4.1.10. Dusty work sites
4.1.11. Avoid mixing oil
4.1.12. Locking inspection covers
4.1.13. Bleeding air from hydraulic circuit
4.1.14. Precautions when installing hydraulic hoses
4.1.15. Checks after inspection and maintenance
4.1.16. Fuel and lubricants to match the ambient temperature
4.1.17. Close engine hood securely
4.2. Outline of service
4.2.1. Handling oil, fuel, coolant, and performing oil clinic
4.2.2. HANDLING ELECTRICAL COMPONENTS
4.3. Standard tightening torque for bolts and nuts
4.3.1. Tightening torque list
4.4. MAINTENANCE SCHEDULE
4.4.1. Maintenance schedule table
4.4.2. MAINTENANCE INTERVAL FOR HYDRAULIC BREAKER
4.5. Maintenance procedure
4.5.1. WHEN REQUIRED
4.5.2. CHECKS BEFORE STARTING
4.5.3. Every 50 hours maintenance
4.5.4. Every 250 hours maintenance
4.5.5. Every 500 hours maintenance
4.5.6. Every 1000 hours maintenance
4.5.7. Every 2000 hours maintenance
4.5.8. Every 4000 hours maintenance
4.5.9. EVERY 4500 HOURS MAINTENANCE
4.5.10. Every 5000 hours maintenance
4.5.11. Every 8000 hours maintenance
4.6. END OF SERVICE LIFE
5. SPECIFICATIONS
5.1. SPECIFICATIONS
6. ATTACHMENTS AND OPTIONS
6.1. GENERAL PRECAUTIONS FOR SAFETY
6.1.1. PRECAUTIONS WHEN SELECTING
6.1.2. Read the operation and maintenance manual thoroughly
6.1.3. PRECAUTIONS WHEN REMOVING OR INSTALLING
6.1.4. PRECAUTIONS WHEN USING
6.2. HANDLING QUICK COUPLER
6.3. AUTOMATIC GREASE SYSTEM
6.3.1. CHECK AUTOGREASING SYSTEM
6.4. Bucket with hook
6.4.1. HOOK CONDITION
6.4.2. Prohibited operations
6.5. Machine ready for installation of attachment
6.5.1. EXPLANATION OF COMPONENTS
6.5.2. HYDRAULIC CIRCUIT
6.5.3. REMOVAL AND INSTALLATION OF ATTACHMENT
6.5.4. ATTACHMENT OPERATIONS
6.5.5. Longterm storage
6.5.6. SPECIFICATIONS
6.5.7. ARM/PIN INFORMATION
6.6. ATTACHMENTS AND OPTIONS
6.6.1. Attachment combinations
6.6.2. TRACK SHOES SELECTION
6.6.3. HANDLING CLAMSHELL BUCKET
6.7. RECOMMENDED ATTACHMENT OPERATIONS
6.7.1. HYDRAULIC BREAKER
6.8. PC36010 STRAIGHT BOOM
6.8.1. GENERAL VIEW OF MACHINE
6.8.2. CAUTION ITEMS
6.8.3. TRANSPORTATION (STRAIGHT BOOM EQUIPMENT)
6.8.4. WORKING RANGE (PC36010 STRAIGHT BOOM)
6.8.5. lifting capacity PC360LCD, PC360NLCD10 STRAIGHT BOOM
7. REPLACEMENT PARTS
7.1. SAFETY CRITICAL PARTS
7.1.1. Safety critical parts list
7.2. Consumable parts
7.2.1. Consumable parts list
7.3. RECOMMENDED FUEL, COOLANT, AND LUBRICANT
7.3.1. LUBRICATION CHART
7.3.2. FUEL, COOLANT, AND LUBRICANTS TO MATCH THE AMBIENT TEMPERATURE
7.3.3. RECOMMENDED BRANDS AND QUALITY FOR PRODUCTS OTHER THAN KOMATSU GENUINE OIL
8. INDEX

Rate this product