komatsu td 20h operation and maintenance manual omtd20h98 1e 1

komatsu td 20h operation and maintenance manual omtd20h98 1e 2

komatsu td 20h operation and maintenance manual omtd20h98 1e 3

komatsu td 20h operation and maintenance manual omtd20h98 1e 4

komatsu td 20h operation and maintenance manual omtd20h98 1e 5

Komatsu TD-20H Operation and Maintenance Manual OMTD20H98-1E

$20.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: OMTD20H98-1E
Format: PDF
Size: 2.2MB
Number of Pages: 165

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- TD-20H

1. MAIN MENU
2. COVER
3. SECTION CONTENTS
4. INTRODUCTION
4.1. INTRODUCTION
4.2. SERIAL NUMBERS
5. SAFETY PRECAUTIONS
5.1. GENERAL
5.2. BEFORE STARTING THE ENGINE
5.3. OPERATION
5.4. MAINTENANCE
5.5. SHUTDOWN
5.6. SAFETY PRODUCT GRAPHIC LOCATION
5.6.1. SAFETY PRODUCT GRAPHIC
6. MACHINE TRANSPORT AND STORAGE
6.1. MACHINE TRANSPORT
6.2. LIFTING MACHINE ON SLINGS
6.3. MOVING A DISABLED MACHINE
6.4. MACHINE STORAGE
6.4.1. PREPARING FOR STORAGE
6.4.2. SERVICING MACHINE DURING STORAGE
6.4.3. PREPARING FOR OPERATION AFTER THE STORAGE
7. OPERATING
7.1. MACHINE PRECAUTIONS
7.2. UNIVERSAL SYMBOLS FOR INSTRUMENTS AND CONTROLS
7.3. INSTRUMENT PANEL
7.4. CAB CONTROLS
7.5. CONTROLS AND ADJUSTMENT
7.5.1. SEAT
7.5.2. SEAT BELT
7.5.3. ENGINE SPEED AND SHUT DOWN LEVER
7.5.4. TRANSMISSION NEUTRAL LOCK LEVER
7.5.5. TRANSMISSION SHIFT LEVER
7.5.6. HAND STEERING LEVERS
7.5.7. BRAKE AND DECELERATOR PEDAL
7.5.8. BRAKE AND DECELERATOR PEDAL LOCK
7.5.9. ELECTRICAL SYSTEM MASTER SWITCH
7.5.10. EQUIPMENT CONTROL LEVERS
7.6. STARTING THE ENGINE
7.6.1. ETHER INJECTOR START
7.6.2. ENGINE START AFTER OIL CHANGE OR PROLONGED STANDSTILL
7.7. STOPPING THE ENGINE
7.8. DRIVING THE MACHINE
7.9. SHIFTING THE TRANSMISSION
7.10. CONVERTER OVERHEATING
7.11. STEERING THE MACHINE
7.12. LOCKING BOTH TRACKS
7.13. DOWNGRADE OPERATION
7.14. OPERATING OVER AN OBSTRUCTION
7.15. STOPPING THE MACHINE
7.16. PARKING THE MACHINE
7.17. OPERATING MOUNTED EQUIPMENT
7.17.1. RIPPER CONTROL LEVER
7.17.2. BULLDOZER BLADE POSITIONS
7.17.3. ANGLING THE BLADE
7.18. OPERATING TECHNIQUES
7.18.1. DIGGING AND CLEARING
7.18.2. TRANSPORTING, PILING OR LOADING
7.18.3. BREAKING PILES AND SPEADING
7.18.4. RIPPING
7.18.4.1. PRIOR TO OPERATION
7.18.4.2. RIPPING TECHNIQUES
7.18.4.3. COLD WEATHER OPERATION
7.19. ECONOMICAL OPERATION OF THE MACHINE
8. MAINTENANCE
8.1. SERVICE PRECAUTIONS
8.2. SCHEDULE MAINTENANCE GUIDE
8.2.1. GROUND LEVEL INSPECTION
8.3. MAINTENANCE AND SERVICE CHART
8.3.1. REFILL SPECIFICATIONS AND CAPACITIES CHART
8.4. LUBRICATION
8.4.1. WHEN SHIPPED
8.4.2. WHEN SERVICED
8.4.3. SELECTION
8.4.4. VISCOSITIES
8.4.5. RECOMMENDED LUBRICATION CHART
8.5. SEASIONAL PREPARATION
8.5.1. FUEL SYSTEM
8.5.2. COOLING SYSTEM
8.5.3. ELECTRICAL SYSTEM
8.6. AIR CLEANING SYSTEM
8.6.1. AIR CLEANER
8.6.2. PRIMARY FILTER ELEMENT
8.6.3. SAFETY FILTER ELEMENT
8.6.4. AIR INTAKE SYSTEM
8.6.4.1. PRECLEANER
8.6.4.2. CHECKING AIR INTAKE SYSTEM FOR LEAKS
8.7. BELTS
8.7.1. CHECKING TENSION AND ADJUSTMENT
8.7.2. BELT TENSION CHART
8.8. COOLING SYSTEM
8.8.1. WATER
8.8.2. ANTIFREEZE
8.8.3. INHIBITORS/ CONDITIONERS
8.8.4. RADIATOR CAP
8.8.5. CHECKING COOLANT LEVEL
8.8.6. CLEANING THE RADIATOR CORE
8.8.7. ADDING THE COOLANT WHEN ENGINE IS HOT
8.8.8. CHANGING COOLANT
8.8.8.1. DRAINING THE SYSTEM
8.8.8.2. FILLING THE DRAIN SYSTEM
8.9. FAN AND FAN HUB
8.10. ELECTRICAL SYSTEM
8.10.1. AUTOMATIC RESET CIRCUIT BREAKER
8.10.2. BATTERIES
8.11. ENGINE
8.11.1. CHECKING THE CRANKCASE OIL
8.11.2. CHANGING THE CRANKCASE OIL AND OIL FILTER
8.11.2.1. CHANGING THE CRANKCASE OIL
8.11.2.2. CHANGING THE ENGINE OIL FILTER
8.11.3. ETHER INJECTOR (IF EQUIPPED)
8.12. FUEL SYSTEM
8.12.1. FILLING THE FUEL TANK
8.12.2. FUEL TANK FILLER STRAINER
8.12.3. FUEL TANK SHUTOFF VALVE
8.12.4. FUEL FILTERS
8.12.4.1. FUEL FILTER WATER SEPERATOR DRAIN VALVE
8.12.4.2. REPLACING THE FUEL FILTER
8.12.5. DRAINING FUEL TANK
8.13. HYDRAULIC SYSTEM
8.13.1. CHECKING OIL LEVEL
8.13.2. CHANGING HYDRAULIC OIL
8.13.3. SERVICING THE RETURN FILTER AND EQUIPMENT HYDRAULIC CONTROL SYSTEM FILTER
8.13.4. SERVICING THE SUCTION STRAINER
8.13.5. SERVICING THE RESERVOIR BREATHER
8.13.6. VENTING THE HYDRAULIC SYSTEM
8.14. LUBRICATION FITTINGS
8.15. MOUNTINED EQUIPMENT
8.15.1. COMPLETE BLADE REMOVAL AND INSTALLATION
8.15.1.1. LEVELING THE BLADE
8.15.1.2. ADJUSTING OF DIAGONAL BLADE WITH HYDRAULIC TILT CYLINDERS
8.15.1.3. FILLING UP AND VENTING THE TILT CYLINDERS OF DIAGONAL BLADE
8.15.1.4. BLADE STRUTS AND TILT CYLINDER ADJUSTMENT
8.15.2. TRUNNION, COVER, BLADE CUTTING EDGE AND END BITS MOUNTING BOLTS
8.15.3. ALLOWABLE WEAR OF CUTTING EDGE AND END BITS AND RIPPER POINTS
8.15.3.1. SERVICING THE RIPPER
8.15.3.2. LUBRICATION
8.16. SAFETY BELT
8.17. FINAL DRIVES
8.17.1. CHECKING THE OIL LEVEL
8.17.2. CHANGING THE OIL
8.18. TRANSMISSION SYSTEM
8.18.1. CHECKING THE OIL LEVEL
8.18.2. CHANGING TRANSMISSION SYSTEM OIL
8.18.3. SERVICING THE TRANSMISSION SYSTEM FILTERS
8.18.3.1. SERVICING THE PRESSURE FILTER
8.18.3.2. SERVICING THE SUCTIO STRAINER
8.18.4. SERVICING THE BREATHER
8.18.5. SERVICING TRANSMISSION SCAVENGER STRAINER
8.19. UNDERCARRIAGE
8.19.1. TRACK SHOE BOLTS
8.19.2. EFFECT OF TRACK ADJUSTMENT ON UNDERCARRIAGE WEAR
8.19.3. CHECKING THE TENSION
8.19.4. ADJUSTING TENSION
8.19.5. TRACK FRAME GUIDE
8.19.6. PIVOT SHAFT
8.19.7. EQUALIZER BAR
8.19.8. FRONT WHEEL
8.20. ADJUSTING HAND AND FOOT CONTROLS
8.21. CAB AND ROPS
9. SPECIFICATIONS
9.1. APPLICATION
9.2. TECHNICAL DESCRIPTION
9.3. KINEMATIC DIAGRAM
9.4. EQUIPMENT HYDRAULIC SYSTEM DIAGRAM
9.5. TRANSMISSION HYDRAULIC SYSTEM DIAGRAM
9.6. WIRING DIAGRAM
9.6.1. CAB WIRING DIAGRAM
9.7. SPECIFICATIONS
9.7.1. OVERALL DIMENSIONS OF DOZER
9.7.2. REFILL CAPACITIES
9.7.3. TRACKS
9.7.4. ENGINE
9.7.5. TORQUE CONVERTER
9.7.6. TRAVEL SPEEDS
9.7.7. WEIGHT (APPROXIMATE)
9.7.8. OPERATION WEIGHTS
9.7.9. ELECTRICAL SYSTEM
9.7.10. FUEL CONSUMPTION
9.8. SPECIAL TORQUES
9.9. STANDARD METRIC FASTENERS
9.10. TORQUE VALUES OF STANDARD ENGLISH FASTENERS
9.11. TORQUE VALUES FOR SPLIT FLANGE CONNECTIONS
9.12. TORQUE VALUES FOR HYDRUALIC TUBES AND FITTINGS
9.13. TORQUE VALUES FOR HOSE CLAMPS
9.14. TORQUE VALUES FOR AIR CONDITIONING TUBES AND FITTINGS
9.15. TORQUE VALUES FOR AIR CONDITIONING ORING CONNECTIONS

Rate this product