komatsu wa400 5h wheel loader operation and maintenance manual veam210100 1

komatsu wa400 5h wheel loader operation and maintenance manual veam210100 2

komatsu wa400 5h wheel loader operation and maintenance manual veam210100 3

komatsu wa400 5h wheel loader operation and maintenance manual veam210100 4

komatsu wa400 5h wheel loader operation and maintenance manual veam210100 5

Komatsu WA400-5H Wheel Loader Operation and Maintenance Manual VEAM210100

$20.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: VEAM210100
Format: PDF
Size: 10.3MB
Number of Pages: 297

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- WA400-5H Wheel Loader

1. WA4005H
2. FOREWORD
2.1. FOREWORD
2.2. SAFETY INFORMATION
2.3. INTRODUCTION
2.3.1. FRONT/REAR, LEFT/RIGHT DIRECTIONS OF MACHINE
2.4. NECESSARY INFORMATION
2.4.1. MACHINE SERIAL NO. PLATE AND POSITION
2.4.2. ENGINE SERIAL NO. PLATE AND POSITION
2.4.3. POSITION OF SERVICE METER
2.4.4. TABLE TO ENTER SERIAL NO. AND DISTRIBUTOR
2.5. CONTENTS
3. SAFETY
3.1. SAFETY
3.2. SAFETY LABELS
3.2.1. LOCATION OF SAFETY LABELS
3.2.2. SAFETY LABELS
3.3. GENERAL PRECAUTIONS
3.4. PRECAUTIONS FOR OPERATION
3.4.1. STARTING ENGINE
3.4.2. OPERATION
3.4.3. TRANSPORTATION
3.4.4. BATTERY
3.4.5. TOWING
3.5. PRECAUTIONS FOR MAINTENANCE
3.6. PRECAUTIONS WITH TIRES
4. OPERATION
4.1. GENERAL VIEW
4.1.1. GENERAL VIEW OF MACHINE
4.1.2. GENERAL VIEW OF CONTROLS AND GAUGES
4.2. EXPLANATION OF COMPONENTS
4.2.1. MACHINE MONITOR
4.2.2. SWITCHES
4.2.3. CONTROL LEVERS, PEDALS
4.2.4. STEERING TILT LOCK LEVER
4.2.5. CAP WITH LOCK
4.2.6. SAFETY BAR
4.2.7. TOWING PIN
4.2.8. GREASE PUMP
4.2.9. CAB DOOR OPEN LOCK
4.2.10. CAB WINDOW OPEN LOCK CANCEL KNOB
4.2.11. BACKUP ALARM
4.2.12. FUSE
4.2.13. SLOWBLOW FUSE
4.2.14. TAKING OFF POWER
4.2.15. AIR CONDITIONER
4.2.16. CAB WIPER
4.2.17. DUST INDICATOR
4.3. OPERATION
4.3.1. CHECK BEFORE STARTING ENGINE, ADJUST
4.3.2. STARTING ENGINE
4.3.3. OPERATIONS AND CHECKS AFTER STARTING ENGINE
4.3.4. STOPPING ENGINE
4.3.5. CHECK AFTER STOPPING ENGINE
4.3.6. MOVING MACHINE OFF (DIRECTIONAL, SPEED), STOPPING
4.3.7. TURNING
4.3.8. OPERATION OF WORK EQUIPMENT
4.3.9. WORKING POSSIBILITY
4.3.10. PRECAUTIONS FOR OPERATION
4.3.11. ADJUSTING WORK EQUIPMENT POSTURE
4.3.12. PARKING MACHINE
4.3.13. CHECKS AFTER COMPLETION OF OPERATION
4.3.14. LOCKING
4.3.15. TIRES
4.4. TRANSPORTATION
4.4.1. TRANSPORTATION PROCEDURE
4.4.2. LOADING, UNLOADING WORK WITH TRAILERS
4.4.3. LIFTING MACHINE
4.5. COLD WEATHER OPERATION
4.5.1. PRECAUTIONS FOR LOW TEMPERATURE
4.5.2. PRECAUTIONS AFTER COMPLETION OF WORK
4.5.3. AFTER COLD WEATHER
4.5.4. WARMINGUP OPERATION FOR STEERING HYDRAULIC CIRCUIT IN COLD WEATHER
4.6. LONGTERM STORAGE
4.6.1. BEFORE STORAGE
4.6.2. DURING STORAGE
4.6.3. AFTER STORAGE
4.7. TROUBLESHOOTING
4.7.1. WHEN MACHINE RUNS OUT OF FUEL
4.7.2. TOWING THE MACHINE
4.7.3. IF BATTERY IS DISCHARGED
4.7.4. OTHER TROUBLE
5. MAINTENANCE
5.1. GUIDES TO MAINTENANCE
5.2. OUTLINES OF SERVICE
5.2.1. OIL, FUEL, COOLANT, AND PERFORMING OIL CLINIC
5.2.2. OUTLINE OF ELECTRIC SYSTEM
5.3. WEAR PARTS
5.3.1. WEAR PARTS LIST
5.4. USE OF FUEL, COOLANT AND LUBRICANTS ACCORDING TO AMBIENT TEMPERATURE
5.4.1. PROPER SELECTION OF FUEL, COOLANT AND LUBRICANTS
5.5. STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS
5.5.1. TORQUE LIST
5.6. PERIODIC REPLACEMENT OF SAFETY CRITICAL PARTS
5.7. MAINTENANCE SCHEDULE CHART
5.7.1. MAINTENANCE SCHEDULE CHART
5.8. SERVICE PROCEDURE
5.8.1. INITIAL 250 HOURS SERVICE
5.8.2. INITIAL 1000 HOURS SERVICE
5.8.3. WHEN REQUIRED
5.8.4. CHECK BEFORE STARTING
5.8.5. EVERY 50 HOURS SERVICE
5.8.6. EVERY 100 HOURS SERVICE
5.8.7. EVERY 250 HOURS SERVICE
5.8.8. EVERY 500 HOURS SERVICE
5.8.9. EVERY 1000 HOURS SERVICE
5.8.10. EVERY 2000 HOURS SERVICE
5.8.11. EVERY 4000 HOURS SERVICE
5.8.12. EVERY 8000 HOURS SERVICE
6. SPECIFICATIONS
6.1. SPECIFICATIONS
7. ATTACHMENTS, OPTIONS
7.1. SELECTING BUCKET AND TIRES
7.2. LOAD METER
7.2.1. GENERAL LOCATIONS
7.2.2. LOAD METER FUNCTIONS
7.2.3. HANDLING LOAD METER DISPLAY
7.2.4. METHOD OF SETTING TIME ON CLOCK
7.2.5. PRINTER OUTPUT
7.3. HANDLING TORQUE CONVERTER LOCKUP
7.3.1. GENERAL LOCATIONS
7.3.2. METHOD OF OPERATION
7.3.3. WARNING/LIMIT FUNCTIONS FOR TRAVEL SPEED
7.4. HANDLING AUTOMATIC AIRCONDITIONER
7.4.1. GENERAL LOCATIONS AND FUNCTIONS OF CONTROL PANEL
7.4.2. METHOD OF OPERATION
7.4.3. PRECAUTIONS WHEN USING
7.4.4. INSPECTION AND MAINTENANCE
7.5. CENTRAL LUBRICATION
7.5.1. OPERATION
7.6. JOYSTICK STEERING SYSTEM
7.6.1. COMPONENTS
7.6.2. STRUCTURE AND FUNCTION OF JOYSTICK STEERING
7.6.3. GETTING IN OR OUT
7.6.4. ADJUSTMENT OF JOYSTICK CONSOLE
7.6.5. OPERATION METHOD OF JOYSTICK STEERING SYSTEM
7.7. EPC WORK EQUIPMENT LEVER
7.7.1. OPERATIONAL FEATURES
7.7.2. SWITCHES
7.7.3. SEMI AUTO DIGGING OPERATIONS
7.7.4. METHOD OF REMOTE POSITIONER
8. INDEX
8.1. INDEX

Rate this product