komatsu wa480 6 wheel loader operation and maintenance manual pen00173 03 1

komatsu wa480 6 wheel loader operation and maintenance manual pen00173 03 2

komatsu wa480 6 wheel loader operation and maintenance manual pen00173 03 3

komatsu wa480 6 wheel loader operation and maintenance manual pen00173 03 4

komatsu wa480 6 wheel loader operation and maintenance manual pen00173 03 5

Komatsu WA480-6 Wheel Loader Operation and Maintenance Manual PEN00173-03

$20.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: PEN00173-03
Format: PDF
Size: 8.5MB
Number of Pages: 335

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- WA480-6 Wheel Loader

1. COVER
2. FOREWORD
2.1. BEFORE READING THIS MANUAL
2.2. SAFETY INFORMATION
2.3. INTRODUCTION
2.3.1. FRONT/REAR, LEFT/RIGHT DIRECTIONS OF MACHINE
2.4. NECESSARY INFORMATION
2.4.1. PRODUCT IDENTIFICATION NUMBER (PIN)/MACHINE SERIAL NO. PLATE
2.4.2. ENGINE SERIAL NO. PLATE
2.4.3. POSITION OF SERVICE METER
2.4.4. TABLE TO ENTER SERIAL NO. AND DISTRIBUTOR
2.5. CONTENTS
3. SAFETY
3.1. SAFETY
3.2. SAFETY LABELS
3.2.1. LOCATION OF SAFETY LABELS
3.2.2. SAFETY LABELS
3.3. GENERAL PRECAUTIONS COMMON TO OPERATION AND MAINTENANCE
3.3.1. PRECAUTIONS BEFORE STARTING OPERATION
3.3.2. PREPARATIONS FOR SAFE OPERATION
3.3.3. FIRE PREVENTION
3.3.4. PRECAUTIONS WHEN GETTING ON OR OFF MACHINE
3.3.5. DO NOT GET CAUGHT IN ARTICULATING PORTION
3.3.6. PRECAUTIONS RELATED TO PROTECTIVE STRUCTURES
3.3.7. UNAUTHORIZED MODIFICATION
3.3.8. PRECAUTIONS RELATED TO ATTACHMENTS AND OPTIONS
3.3.9. PRECAUTIONS WHEN RUNNING ENGINE INSIDE BUILDING
3.4. PRECAUTIONS FOR OPERATION
3.4.1. PRECAUTIONS FOR JOBSITE
3.4.2. STARTING ENGINE
3.4.3. OPERATION
3.4.4. TRANSPORTATION
3.4.5. TOWING
3.5. PRECAUTIONS FOR MAINTENANCE
3.5.1. PRECAUTIONS BEFORE STARTING INSPECTION AND MAINTENANCE
3.5.2. PRECAUTIONS FOR INSPECTION AND MAINTENANCE
3.5.3. TIRES
4. OPERATION
4.1. GENERAL VIEW
4.1.1. GENERAL VIEW OF MACHINE
4.1.2. GENERAL VIEW OF CONTROLS AND GAUGES
4.2. EXPLANATION OF COMPONENTS
4.2.1. MACHINE MONITOR
4.2.2. SWITCHES
4.2.3. CONTROL LEVERS, PEDALS
4.2.4. STEERING TILT LOCK LEVER
4.2.5. CAP WITH LOCK
4.2.6. FRAME LOCK BAR
4.2.7. TOWING PIN
4.2.8. GREASE PUMP
4.2.9. OPENING CAB, WINDOW DOOR
4.2.10. BACKUP ALARM
4.2.11. FUSE
4.2.12. SLOW BLOW FUSE
4.2.13. POWER OUTLET
4.2.14. AM/FM RADIOCASSETTE STEREO
4.2.15. AM/FM RADIO
4.2.16. AIR CONDITIONER
4.2.17. HANDLING AUTO AIR CONDITIONER
4.2.18. HANDLING CAB WIPER
4.3. OPERATION
4.3.1. CHECK BEFORE STARTING ENGINE, ADJUST
4.3.2. STARTING ENGINE
4.3.3. CHECKS AFTER STARTING ENGINE
4.3.4. OPERATIONS AND CHECKS AFTER STARTING ENGINE
4.3.5. STOPPING ENGINE
4.3.6. MOVING THE MACHINE (DIRECTIONAL, SPEED), STOPPING THE MACHINE
4.3.7. TURNING
4.3.8. OPERATION OF WORK EQUIPMENT
4.3.9. WORK POSSIBLE USING WHEEL LOADER
4.3.10. PRECAUTIONS FOR OPERATION
4.3.11. ADJUSTING WORK EQUIPMENT POSTURE
4.3.12. PARKING MACHINE
4.3.13. CHECKS AFTER COMPLETION OF OPERATION
4.3.14. LOCKING
4.3.15. HANDLING THE TIRES
4.4. TRANSPORTATION
4.4.1. TRANSPORTATION PROCEDURE
4.4.2. LOADING, UNLOADING WORK WITH TRAILERS
4.4.3. LIFTING MACHINE
4.5. COLD WEATHER OPERATION
4.5.1. PRECAUTIONS FOR LOW TEMPERATURE
4.5.2. PRECAUTIONS AFTER COMPLETION OF WORK
4.5.3. AFTER COLD WEATHER
4.6. LONGTERM STORAGE
4.6.1. BEFORE STORAGE
4.6.2. DURING STORAGE
4.6.3. AFTER STORAGE
4.7. TROUBLESHOOTING
4.7.1. WHEN MACHINE RUNS OUT OF FUEL
4.7.2. METHOD OF TOWING MACHINE
4.7.3. IF BATTERY IS DISCHARGED
4.7.4. OTHER TROUBLE
5. MAINTENANCE
5.1. GUIDES TO MAINTENANCE
5.2. OUTLINES OF SERVICE
5.2.1. HANDLING OIL, FUEL, COOLANT, AND PERFORMING OIL CLINIC
5.2.2. OUTLINE OF ELECTRIC SYSTEM
5.3. WEAR PARTS
5.3.1. WEAR PARTS LIST
5.4. RECOMMENDED FUEL, COOLANT, AND LUBRICANT
5.4.1. USE OF FUEL, COOLANT AND LUBRICANTS ACCORDING TO AMBIENT TEMPERATURE
5.4.2. RECOMMENDED BRANDS, RECOMMENDED QUALITY FOR PRODUCTS OTHER THAN KOMATSU GENUINE OIL
5.5. STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS
5.5.1. TORQUE LIST
5.6. PERIODIC REPLACEMENT OF SAFETY CRITICAL PARTS
5.7. MAINTENANCE SCHEDULE CHART
5.7.1. MAINTENANCE SCHEDULE CHART
5.8. SERVICE PROCEDURE
5.8.1. INITIAL 250 HOURS SERVICE
5.8.2. INITIAL 1000 HOURS SERVICE
5.8.3. WHEN REQUIRED
5.8.4. CHECK BEFORE STARTING
5.8.5. EVERY 50 HOURS SERVICE
5.8.6. EVERY 100 HOURS SERVICE
5.8.7. EVERY 250 HOURS SERVICE
5.8.8. EVERY 500 HOURS SERVICE
5.8.9. EVERY 1000 HOURS SERVICE
5.8.10. EVERY 2000 HOURS SERVICE
5.8.11. EVERY 4000 HOURS SERVICE
5.8.12. EVERY 8000 HOURS SERVICE
6. SPECIFICATIONS
6.1. SPECIFICATIONS
7. ATTACHMENTS, OPTIONS
7.1. SELECTING BUCKET AND TIRES
7.2. HANDLING TORQUE CONVERTER LOCKUP
7.2.1. GENERAL LOCATIONS
7.2.2. METHOD OF OPERATION
7.2.3. WARNING/LIMIT FUNCTIONS FOR TRAVEL SPEED
7.3. HANDLING JOYSTICK STEERING SYSTEM
7.3.1. EXPLANATION OF COMPONENTS
7.3.2. STRUCTURE AND FUNCTION OF JOYSTICK STEERING
7.3.3. GETTING IN OR OUT OF OPERATORS CAB
7.3.4. SEAT ADJUSTMENT
7.3.5. ADJUSTMENT OF JOYSTICK CONSOLE
7.3.6. OPERATION USING JOYSTICK LEVER AND OPERATION USING STEERING WHEEL
7.3.7. PRECAUTIONS FOR STEERING WITH JOYSTICK
7.3.8. OPERATION METHOD OF JOYSTICK STEERING SYSTEM
7.4. HANDLING MULTIFUNCTION LEVER
7.4.1. EXPLANATION OF COMPONENTS
7.4.2. USING FNR SWITCH TO CHANGE BETWEEN FORWARD AND REVERSE
7.5. HANDLING MACHINES EQUIPPED WITH KOMTRAX
7.5.1. BASIC PRECAUTIONS
8. INDEX

Rate this product