komatsu wa700 3 wheel loader operation and maintenance manual ten00297 03 1

komatsu wa700 3 wheel loader operation and maintenance manual ten00297 03 2

komatsu wa700 3 wheel loader operation and maintenance manual ten00297 03 3

komatsu wa700 3 wheel loader operation and maintenance manual ten00297 03 4

komatsu wa700 3 wheel loader operation and maintenance manual ten00297 03 5

Komatsu WA700-3 Wheel Loader Operation and Maintenance Manual TEN00297-03

$20.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: TEN00297-03
Format: PDF
Size: 6.3MB
Number of Pages: 299

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- WA700-3 Wheel Loader

1. COVER
2. FOREWORD
2.1. FOREWORD
2.2. SAFETY INFORMATION
2.3. INTRODUCTION
2.3.1. FRONT/REAR, LEFT/RIGHT DIRECTIONS OF MACHINE
2.3.2. VISIBILITY FROM OPERATORS SEAT
2.4. NECESSARY INFORMATION
2.4.1. PRODUCT IDENTIFICATION NUMBER (PIN)/MACHINE SERIAL NO. PLATE
2.4.2. ENGINE SERIAL NO. PLATE AND POSITION
2.4.3. POSITION OF SERVICE METER
2.4.4. TABLE TO ENTER SERIAL NO. AND DISTRIBUTOR
2.5. CONTENTS
3. SAFETY
3.1. SAFETY
3.1.1. SAFETY LABELS
3.1.2. LOCATION OF SAFETY LABELS
3.2. GENERAL PRECAUTIONS
3.3. PRECAUTIONS FOR OPERATION
3.3.1. STARTING ENGINE
3.3.2. OPERATION
3.3.3. TRANSPORTATION
3.3.4. BATTERY
3.3.5. TOWING
3.3.6. PRECAUTIONS FOR MAINTENANCE
3.3.7. PRECAUTIONS WITH TIRES
4. OPERATION
4.1. GENERAL VIEW
4.1.1. GENERAL VIEW OF MACHINE
4.1.2. GENERAL VIEW OF CONTROLS AND GAUGES
4.2. EXPLANATION OF COMPONENTS
4.2.1. MACHINE MONITOR
4.2.2. SWITCHES
4.2.3. CONTROL LEVERS, PEDALS
4.2.4. STEERING COLUMN TILT LEVER
4.2.5. CAP WITH LOCK
4.2.6. FUEL STOP LEVER FOR EMERGENCY ENGINE STOP
4.2.7. FRAME LOCK BAR
4.2.8. TOWING PIN
4.2.9. GREASE PUMP
4.2.10. BACKUP ALARM
4.2.11. CAB DOOR OPEN LOCK
4.2.12. PRECAUTIONS WHEN HANDLING ACCUMULATOR
4.3. OPERATION
4.3.1. CHECK BEFORE STARTING ENGINE, ADJUST
4.3.2. STARTING ENGINE
4.3.3. OPERATIONS AND CHECKS AFTER STARTING ENGINE
4.3.4. STOPPING ENGINE
4.3.5. CHECK AFTER STOPPING ENGINE
4.3.6. MOVING THE MACHINE (DIRECTIONAL, SPEED), STOPPING THE MACHINE
4.3.7. TURNING
4.3.8. OPERATION OF WORK EQUIPMENT
4.3.9. WORK POSSIBLE USING WHEEL LOADER
4.3.10. PRECAUTIONS FOR OPERATION
4.3.11. ADJUSTING WORK EQUIPMENT POSTURE
4.3.12. REMOVAL AND INSTALLATION OF THE BUCKET
4.3.13. PARKING MACHINE
4.3.14. CHECKS AFTER COMPLETION OF OPERATION
4.3.15. LOCKING
4.3.16. HANDLING THE TIRES
4.4. TRANSPORTATION
4.4.1. TRANSPORTATION PROCEDURE
4.4.2. LOADING, UNLOADING WORK
4.4.3. METHOD OF SECURING MACHINE
4.4.4. METHOD OF LIFTING MACHINE
4.5. COLD WEATHER OPERATION
4.5.1. PRECAUTIONS FOR LOW TEMPERATURE
4.5.2. PRECAUTIONS AFTER COMPLETION OF WORK
4.5.3. AFTER COLD WEATHER
4.5.4. WARMINGUP OPERATION FOR STEERING HYDRAULIC CIRCUIT IN COLD WEATHER
4.6. LONGTERM STORAGE
4.6.1. BEFORE STORAGE
4.6.2. DURING STORAGE
4.6.3. AFTER STORAGE
4.7. TROUBLESHOOTING
4.7.1. WHEN MACHINE RUNS OUT OF FUEL
4.7.2. METHOD OF TOWING MACHINE
4.7.3. IF BATTERY IS DISCHARGED
4.7.4. OTHER TROUBLE
5. MAINTENANCE
5.1. GUIDES TO MAINTENANCE
5.2. OUTLINES OF SERVICE
5.2.1. HANDLING OIL, FUEL, COOLANT, AND PERFORMING OIL CLINIC
5.2.2. OUTLINE OF ELECTRIC SYSTEM
5.3. WEAR PARTS
5.3.1. WEAR PARTS LIST
5.4. RECOMMENDED FUEL, COOLANT, AND LUBRICANT
5.4.1. USE OF FUEL, COOLANT AND LUBRICANTS ACCORDING TO AMBIENT TEMPERATURE
5.4.2. RECOMMENDED BRANDS, RECOMMENDED QUALITY FOR PRODUCTS OTHER THAN KOMATSU GENUINE OIL
5.5. STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS
5.5.1. TORQUE LIST
5.6. PERIODIC REPLACEMENT OF SAFETY CRITICAL PARTS
5.6.1. SAFETY CRITICAL PARTS
5.7. MAINTENANCE SCHEDULE CHART
5.7.1. MAINTENANCE SCHEDULE CHART
5.8. SERVICE PROCEDURE
5.8.1. INITIAL 250 HOURS SERVICE
5.8.2. INITIAL 2000 HOURS SERVICE
5.8.3. WHEN REQUIRED
5.8.4. CHECK BEFORE STARTING
5.8.5. EVERY 50 HOURS SERVICE
5.8.6. EVERY 100 HOURS SERVICE
5.8.7. EVERY 250 HOURS SERVICE
5.8.8. EVERY 500 HOURS SERVICE
5.8.9. EVERY 1000 HOURS SERVICE
5.8.10. EVERY 2000 HOURS SERVICE
5.8.11. EVERY 4000 HOURS SERVICE
6. SPECIFICATIONS
6.1. SPECIFICATIONS
7. ATTACHMENTS, OPTIONS
7.1. SELECTING BUCKET AND TIRES
7.2. HANDLING AUTOGREASING SYSTEM
7.2.1. METHOD OF OPERATING AUTOGREASING SYSTEM
7.2.2. PRECAUTIONS WHEN HANDLING AUTOGREASING SYSTEM
7.2.3. METHOD OF ADJUSTING DISCHARGE FROM INJECTOR
7.2.4. METHOD OF SETTING TIMER
7.3. HANDLING AUTOMATIC SHIFT SYSTEM
7.3.1. METHOD OF OPERATION
7.3.2. PRECAUTION WHEN CHANGING DIRECTION
7.4. HANDLING AJSS (ADVANCED JOYSTICK STEERING SYSTEM)
7.4.1. EXPLANATION OF COMPONENTS
7.4.2. STRUCTURE AND FUNCTION OF JOYSTICK STEERING
7.4.3. OPERATION METHOD OF JOYSTICK STEERING SYSTEM
7.4.4. ADJUSTMENT OF JOYSTICK CONSOLE
7.4.5. ADJUSTMENT OF AIR SUSPENSION SEAT
7.5. FAILURE DISPLAY ON MAIN MONITOR
7.5.1. FAILURE CODE ON MAIN MONITOR
7.6. CAR RADIO
7.6.1. EXPLANATION OF COMPONENTS
7.6.2. METHOD OF USE
7.6.3. PRECAUTIONS WHEN USING
7.7. AM/FM RADIOCASSETTE STEREO
7.7.1. EXPLANATION OF COMPONENTS
7.7.2. METHOD OF OPERATION
7.7.3. PRECAUTIONS FOR USE
7.8. AIR CONDITIONER
7.8.1. GENERAL LOCATIONS AND FUNCTION OF CONTROL PANEL
7.8.2. METHOD OF OPERATION
8. INDEX

Rate this product