komatsu wh609 1e0 wh613 1e0 wh713 1e0 wh714h 1e0 wh716 1e0 telescopic handler shop manual webm008500 1

komatsu wh609 1e0 wh613 1e0 wh713 1e0 wh714h 1e0 wh716 1e0 telescopic handler shop manual webm008500 2

komatsu wh609 1e0 wh613 1e0 wh713 1e0 wh714h 1e0 wh716 1e0 telescopic handler shop manual webm008500 3

komatsu wh609 1e0 wh613 1e0 wh713 1e0 wh714h 1e0 wh716 1e0 telescopic handler shop manual webm008500 4

komatsu wh609 1e0 wh613 1e0 wh713 1e0 wh714h 1e0 wh716 1e0 telescopic handler shop manual webm008500 5

Komatsu WH609-1E0, WH613-1E0, WH713-1E0, WH714H-1E0, WH716-1E0 Telescopic Handler Shop Manual WEBM008500

$40.00

Type Of Manual: Shop Manual
Manual ID: WEBM008500
Format: PDF
Size: 60.4MB
Number of Pages: 496

Category: Komatsu Shop Manual PDF

Model List:
- WH609-1E0 Telescopic Handler
- WH613-1E0 Telescopic Handler
- WH713-1E0 Telescopic Handler
- WH714H-1E0 Telescopic Handler
- WH716-1E0 Telescopic Handler

1. CONTENTS
2. REVISED PAGES
3. k SAFETY
4. FOREWORD
5. HOW TO READ THE SHOP MANUAL
6. HOISTING INSTRUCTIONS
7. STANDARD TIGHTENING TORQUE
8. COATING MATERIALS
9. ELECTRIC
10. WEIGHT TABLE
11. TABLE OF OIL AND COOLANT QUANTITIES
12. CONVERSION TABLE
13. STRUCTURE AND FUNCTION
13.1. ENGINETRANSMISSION COUPLING
13.2. STEERING SYSTEM (4WS)
13.3. STEERING UNIT
13.4. HYDRAULIC DIAGRAM
13.5. HYDRAULIC PUMP
13.6. CONTROL VALVE
13.7. PPC VALVE
13.8. SOLENOID VALVES
13.9. SAFETY VALVES
13.10. CYLINDERS
13.11. AIR CONDITIONING SYSTEM
13.12. CLIMATE CONTROL SYSTEM OPERATION
14. TESTING AND ADJUSTMENTS
14.1. STANDARD SPECIFICATIONS
14.2. INTRODUCTION
14.3. VALVE LASH ADJUSTMENT
14.4. CHECKING ENGINE SPEED
14.5. TENSIONING THE AIR CONDITIONER COMPRESSOR BELT
14.6. ADJUSTING ACCELERATOR CABLE LENGTH
14.7. ADJUSTING BRAKE PEDAL TRAVEL AND POSITIONING THE STOP LAMP MICROSWITCHES
14.8. ADJUSTING THE PARKING BRAKES
14.9. BLEEDING AIR FROM CIRCUITS
14.10. PREPARING THE MACHINE READY FOR HYDRAULIC PRESSURE CHECK AND CALIBRATION
14.11. CHECKING AND CALIBRATING WORK EQUIPMENT HYDRAULIC PRESSURES
14.12. CALIBRATING THE PRESSURE OF THE STEERING SYSTEM
14.13. INSPECTING THE OPERATION OF THE UNLOADING VALVE
14.14. CHECKING AND CALIBRATING THE DR VALVE (PUMP FLOW VARIATION)
14.15. CHECKING THE DYNAMIC PUMP DP VALUE
14.16. CHECKING PUMP FLOW
14.17. BRAKE SYSTEM CHECKS
14.18. TRANSMISSION (POWER SHIFT) CHECKS
14.19. TRANSMISSION ASSEMBLY PRESSURE CHECKS
14.20. CHECKING THE SPEED OF THE TRANSMISSION SHAFTS RESPONSIBLE FOR TRANSLATION (CARDAN SHAFTS)
14.21. LEVEL CALIBRATION
14.22. CHECKING LOAD CELL CALIBRATION
14.23. CALIBRATING THE OVERTURN PREVENTION SYSTEM (STANDARD)
14.24. CALIBRATING THE OVERTURN PREVENTION (ASM) CONTROL UNIT
14.25. CHECKING LED CALIBRATION (version with ASM)
14.26. CHECKING SLIDING PADS CLEARANCE
14.27. CHECKING BOOM SIDE ALIGNMENT
14.28. BOOM CHAINS
14.29. CHAIN TENSIONING
14.30. CHECKING FOR BLOWBY
14.31. ANALYSIS OF THE CAUSES RESPONSIBLE FOR HYDRAULIC DRIFT
14.32. EQUALIZING STABILIZER SPEED
14.33. AIR CONDITIONING SYSTEM MAINTENANCE
14.34. CHECKING THE A/C SYSTEMS OPERATING TEMPERATURE
15. REMOVAL AND INSTALLATION
15.1. HOW TO READ THE MANUAL
15.2. PRECAUTIONS TO BE TAKEN WHEN WORKING
15.3. TURBOCOMPRESSOR
15.4. RADIATOREXCHANGER ASSEMBLY
15.5. BATTERY BATTERY TRAY
15.6. COMPLETE ENGINE SHIFT ASSEMBLY
15.6.1. Removal
15.6.2. Installation
15.7. ENGINETRANSMISSION
15.7.1. Detachment
15.7.2. Joining
15.8. CONTROL VALVE ASSEMBLY
15.8.1. Removal
15.8.2. Installation
15.9. BRACKET CONTROL, EQUIPMENT LOCK, AND FRAME LEVELLING SOLENOID VALVES
15.9.1. Removal
15.9.2. Installation
15.10. AIR CONDITIONER COMPRESSOR (only if equipped)
15.10.1. Removal
15.10.2. Installation
15.11. COMPRESSOR BELT
15.11.1. Removal
15.11.2. Installation
15.12. SERVOCONTROL FEED VALVE
15.12.1. Removal
15.12.2. Installation
15.13. STEERING SELECTION SOLENOID VALVE ASSEMBLY
15.13.1. Removal
15.13.2. Installation
15.14. FRONT AXLE
15.14.1. Preparation
15.14.1.1. . Machine with outriggers
15.14.1.2. . Machine without outriggers
15.14.1.3. Removal
15.14.1.4. Installation
15.15. REAR AXLE
15.15.1. Preparation
15.15.1.1. . Machine with outriggers
15.15.1.2. . Machine without outriggers
15.15.1.3. Removal
15.15.1.4. Installation
15.16. TELESCOPIC BOOM
15.16.1. Removal
15.16.2. Installation
15.17. LIFT AND OFFSET CYLINDERS
15.17.1. Removal
15.17.2. Installation
15.18. INTERMEDIATE AND TOP BOOM
15.18.1. Removal
15.18.2. Installation
15.19. EXTENSION CYLINDER
15.19.1. Removal
15.19.2. Installation
15.20. BOOM SLIDING PADS
15.20.1. Replacement
15.20.1.1. Lower sliding pads for intermediate and top booms.
15.20.1.2. Upper sliding pads for intermediate boom
15.20.1.3. Side sliding pads for intermediate and top boom
15.20.1.4. Upper sliding pads for top boom
15.20.1.5. Rear upper sliding pads for intermediate boom
15.20.1.6. Rear upper sliding pads for top boom
15.20.1.7. Rear lower sliding pads for intermediate and top boom
15.21. EXTENSION AND RETRACTION CHAINS (Versions with 3section boom)
15.21.1. Removal
15.21.2. Installation
15.22. CHAIN RETURN PULLEY PINS AND BUSHINGS
15.22.1. RETRACTION CHAIN PULLEY
15.22.1.1. Removal
15.22.1.2. Installation
15.22.2. EXTENSION CHAIN PULLEYS
15.23. ENGINE LINE CENTRE
15.23.1. Removal
15.23.2. Installation
15.24. ACCELERATOR CABLE
15.24.1. Removal
15.24.2. Installation
15.25. SHIFTREVERSING GEAR LEVER ASSEMBLY
15.25.1. Removal
15.25.2. Installation
15.26. STEERING COLUMN SWITCH UNIT DIPSWITCH
15.26.0.1. . Removing the seals
15.26.0.2. . Removing the wiper ring
15.26.1. Assembly
15.26.1.1. . Installing the inner seal (15)
15.26.1.2. . Installing the control valve
15.26.1.3. . Completing the installation procedure
15.27. STEERING COLUMN
15.27.1. . Front wiper motor
15.27.2. . Rear wiper motor
15.27.3. . Upper wiper motor
15.27.4. Installation
15.28. PARKING BRAKE CABLE
15.28.1. Removal
15.28.2. Installation
15.29. DASH / INSTRUMENT PANEL
15.30. FUSE AND RELAY CENTRE
15.30.1. Removal
15.30.2. Installation
15.31. PROPELLER SHAFT
15.31.1. Removal
15.31.2. . Front cardan shaft
15.31.3. . Rear cardan shaft
15.31.4. Installation
15.32. FUEL TANK
15.32.1. Removal
15.32.2. Installation
15.33. HYDRAULIC OIL TANK
15.33.1. Removal
15.33.2. Installation
15.34. FRAME LEVELLING CYLINDER
15.34.1. Removal
15.34.2. Installation
15.35. FRAME SWING LOCKING ROD (WH609 and WH613 only)
15.35.1. Removal
15.35.2. Installation
15.36. AXLE LOCKING CYLINDER
15.36.1. Removal
15.36.2. Installation
15.37. STABILIZER CYLINDERS (If equipped)
15.37.1. Removal
15.37.2. Installation
15.38. EQUIPMENT HOLDER
15.38.1. Removal
15.38.2. Installation
15.39. EQUIPMENT MOTION CYLINDER
15.40. EQUIPMENT QUICKLOCK ASSEMBLY
15.40.1. Removal
15.40.2. Installation
15.41. AIR CONDITIONER FANS
15.41.1. Removal
15.41.2. Installation
15.42. AIR CONDITIONER CONDENSER ASSEMBLY
15.42.1. Removal
15.42.2. Installation
15.43. DEHUMIDIFYING FILTER
15.43.1. Removal
15.43.2. Installation
15.44. AIR CONDITIONING SYSTEM PRESSURE SWITCH
15.44.1. TRANSMISSION ASSEMBLY
15.44.2. PRESSURE REGULATOR VALVE
15.44.3. Disassembly
15.44.4. Assembly
15.44.5. MODULATED VALVE
15.44.6. CONVERTER HOUSING
15.44.7. Disassembly
15.44.8. Assembly
15.44.9. DROP BOX ASSEMBLY
15.44.10. Disassembly
15.44.10.1. . Complete drop box assembly
15.44.10.2. . Input shaft
15.44.11. Assembly
15.44.11.1. . Input shaft
15.44.11.2. . Complete drop box assembly
15.45. AXLES
15.45.1. Disassembly
15.45.1.1. . Planetary reduction
15.45.1.2. . Steering case
15.45.1.3. . Cardan shaft
15.45.1.4. . Brakes
15.45.1.5. . Parking brake assembly (front axle)
15.45.1.6. . Removal of steering cylinder
15.45.1.7. . Disassembly of steering cylinder
15.45.1.8. . Steering cylinder
15.45.1.9. . Steering cylinder
15.45.1.10. . Convergency adjustment
15.45.1.11. . Parking brake assembly (front axle)
15.45.1.12. . Brakes
15.45.1.13. . Cardan shaft
15.45.1.14. . Steering case
15.45.1.15. . Planetary reduction

Rate this product