Claas C490-C300 LEXION TUCANO (527) Combine Operator Manual PL

File List:

– 00 0294 985 1.pdf
– 00 0294 985 5.pdf

00 0294 985 1.pdf

Table of Content:
1 Table of contents
2 1 Introduction
2.1 1.1 General instructions
2.2 1.2 Nameplate and identification numbers
3 2 Security
3.1 2.1 General instructions
3.2 2.2 General security measures
3.3 2.3 Safety instructions
3.4 2.4 Warning symbols
4 3 Technical data
4.1 3.1 C490 / C430 / C370 – TYPE 527
5 4 Before first run
5.1 4.1 General instructions
5.2 4.2 Lift
6 5 Before each start
6.1 5.1 General information
6.2 5.2 Immersive Team
7 6 Coupling/uncoupling work attachment
7.1 6.1 General information
7.2 6.2 General installation and settings
7.3 6.3 Output drives / drives
7.4 6.4 Hydraulics
7.5 6.5 Attached parts / Machine housing
8 7 Setting the working position
8.1 7.1 General information
8.2 7.2 Cutting unit
9.1 8.1 General information
9.2 8.2 General operation
9.3 8.3 Picking up material
9.4 8.4 Immersive Team
10 9 Faults and their removal
10.1 9.1 General information
10.2 9.2 General faults and their removal
10.3 9.3 Hydraulics
10.4 9.4 Picking up material
11 10 Maintenance
11.1 10.1 General information
11.2 10.2 General warnings
11.3 10.3 Maintenance table
11.4 10.4 Lubricant table
11.5 10.5 Transmission / clutch
11.6 10.6 Drives / receiving drives
11.7 10.7 Cutting unit
12 11 Lubrication plan
12.1 11.1 General information
12.2 11.2 Lubrication points
13 Index hase

00 0294 985 5.pdf

Table of Content:
1 User manual
2 Table of contents
3 1 Introductioety labeling
4.4 2.4 Security devices
5 3 Machine description
5.1 3.1 Overview and operation
5.2 3.2 Nameplates and identification numbers
5.3 3.3 Machine Information
6 4 Technical data
6.1 4.1 Standard cutterbar
6.2 4.2 Consumables
7 5 Preparing the machine
7.1 5.1 Machine shutdown and protection
7.2 5.2 Before starting
7.3 5.3 Loading the front attachment
7.4 5.4 Coupling the front attachment
7.5 5.5 Disconnect front attachment
8 6 Service
8.1 6.1 Driving the machine
8.2 6.2 Steering
8.3 6.3 Downloading material
8.4 6.4 Feed unit
8.5 6.5 Cutting unit
8.6 6.6 Ground guidance
9 7 Faults and their removal
9.1 7.1 Causes and their removal
9.2 7.2 Downloading material
9.3 7.3 Feed unit
9.4 7.4 Cutting unit
10 8 Maintenance
10.1 8.1 Maintenance intervals
10.2 8.2 Lubrication plan
10.3 8.3 Transmission, clutch and drive shaft
10.4 8.4 Drives
10.5 8.5 Hydraulics
10.6 8.6 Cutting unit
11 9 Decommissioning and disposal
11.1 9.1 General information
12 10 Declaration of Conformity
12.1 10.1 Front attachment