Claas C680-C440 (318) Combines Operator Manual FR

File List:

00 0305 108 3.pdf

00 0305 108 3.pdf:

Instructions for use
Contents
1 Introduction
1.1 General instructions
1.1.1 Validity of the notice
1.1.2 Information regarding this user manual
1.1.3 Icons and notes
1.1.4 Optional equipment
1.1.5 Qualified specialist workshop
1.1.6 Notes on maintenance
1.1.7 Notes regarding warranty
1.1.8 Spare parts and technical questions
1.2 Use in accordance with instructions
1.2.1 Use in accordance with instructions
1.2.2 Reasonably foreseeable misuse
2 Security
2.1 Recognize the warnings
2.1.1 Warning pictogram
2.1.2 Signal word
2.2 Safety tips
2.2.1 Meaning of the instructions for use
2.2.2 Observe warning pictograms and warnings
2.2.3 Requirements for all people who work with the machine
2.2.4 Dangerous areas
2.2.5 Do not stand between the machine and the front tool
2.2.6 Couple the machine with the front tool or cutting carriage
2.2.7 Risk of injury due to rotating shafts
2.2.8 Constructive modifications
2.2.9 Optional equipment and spare parts
2.2.10 Operation only after proper commissioning
2.2.11 Technical condition
2.2.12 Risks in the event of damage to the machine
2.2.13 Maintain safety devices in operational capacity
2.2.14 Personal safety equipment
2.2.15 Wear suitable clothing
2.2.16 Remove dirt and loose objects
2.2.17 Prepare the machine for road travel
2.2.18 Inappropriate operating consumables
2.2.19 Safety in handling operating consumables and secondary consumable materials
2.2.20 Environmental protection and disposal
2.2.21 Electric shock from the electrical system
2.2.22 Liquids under pressure
2.2.23 Work only on the stopped machine
2.2.24 Maintenance and repair work
2.2.25 Machine elements recorded and loads
2.2.26 Risks due to welding work
2.3 Safety marking
2.3.1 Structure of warning pictograms
2.3.2 Warning pictograms on the front tool
3 Description of the machine
3.1 Overview and mode of operation
3.1.1 Overview of the front tool
3.1.2 Operating mode of the front tool
3.1.3 Operating mode of overload safety
3.2 Nameplates and identification numbers
3.2.1 Front tool nameplate
3.3 Machine information
3.3.1 Sticker
4 Technical characteristics
4.1 Front tool
4.1.1 Authorized machines
4.1.2 Dimensions
4.1.3 Weight
4.1.4 Reel
4.1.5 Feed auger
4.1.6 Cutting widths
4.2 Operating consumables
4.2.1 Lubricants
5 Preparing the machine
5.1 Stop and immobilize the machine
5.1.1 Stop and immobilize the machine.
5.2 Load the front tool
5.2.1 Load the front implement and secure it
5.3 Install the front tool
5.3.1 Install the front tool
5.3.2 Hanging the front tool
5.3.3 Lock the front tool
5.3.4 Install the cardan shaft
5.3.5 Hanging the PTO shaft protection chain
Hang the chain
Check chain length
5.3.6 Connect electrical cables and hydraulic lines
5.3.7 Remove the stands
5.4 Remove the front tool
5.4.1 Remove the front tool
5.4.2 Install the crutches
5.4.3 Disconnect electrical cables and hydraulic lines
5.4.4 Remove the cardan shaft
5.4.5 Unlock the front tool
5.4.6 Unhook the front tool
5.5 Harvest collection
5.5.1 Install the reel safety supports
5.5.2 Loosen the reel safety supports
5.6 Cutting device
5.6.1 Install the cutter bar protection device
6.1 Driving the machine
6.1.1 Prepare for road travel
6.2 Work
6.2.1 Prepare to move into the field
6.2.2 Check crop absorption
6.3 Harvest collection
6.3.1 Adjust the reel horizontally
6.3.2 Mount the divider
6.3.3 Remove the divider
6.3.4 Adjust the divider
6.3.5 Adjust the reel fingers
6.4 Feed auger
6.4.1 Adjust the scraper profiles of the feed auger
6.4.2 Adjust the position of the feed auger
6.4.3 Adjust the feed auger fingers
6.4.4 Remove the worm sheet extensions
6.5 Cutting device
6.5.1 Install the corn lifter
6.5.2 Remove the corn lifter
6.6 Ground guidance
6.6.1 Adjust the skates
7 Faults and solutions
7.1 Overview of faults
7.1.1 Improve harvest flow
7.1.2 Harvest collection
7.1.3 Feed auger
7.1.4 Mower
7.1.5 Ground guidance
7.2 Hydraulic system
7.2.1 Bleed air from reel hydraulic cylinders
7.3 Harvest collection
7.3.1 Check the basic reel height setting
7.3.2 Replacing the reel fingers
7.4 Feed auger
7.4.1 Replace the feed auger fingers
8 Maintenance
8.1 Maintenance intervals
8.1.1 Before the start of the harvest
8.1.2 Every 10 operating hours or every day
8.1.3 After the first 100 hours of operation
8.1.4 Every 100 operating hours
8.1.5 Every 250 operating hours
8.1.6 After harvest
8.1.7 Preservation measures for the front tool
8.2 Lubrication plan
8.2.1 Lubricate the lubrication points every 10 operating hours
8.2.2 Lubricate the lubrication points every 100 operating hours
8.2.3 Lubricate the lubrication points every 250 operating hours
8.3 Preparing for maintenance
8.3.1 Opening and closing the side hatch
Adjust the lever
Remove the front cover
Install the front cover
Close the side hatch
8.4 Workouts
8.4.1 Setting drives
8.4.2 Adjust the belt (R01)
8.4.3 Remove the chain (K01)
8.4.4 Install the chain (K01)
8.4.5 Adjust the chain (K01)
8.4.6 Remove the chain (K02)
8.4.7 Install the chain (K02)
8.4.8 Adjust the chain (K02)
8.5 Hydraulic system
8.5.1 Check hydraulic hoses
Marking of hydraulic hoses
8.6 Cutting device
8.6.1 Replacing the knives
8.6.2 Check equalizers
Check Low Equalizers
Check the wear plate
Check the high equalizer for wear
Check high equalizer
8.6.3 Replace the blade section
8.6.4 Replace double fingers
8.7 Ground guidance
8.7.1 Cleaning the skates
9 Decommissioning and disposal
9.1 General instructions
9.1.1 Decommissioning and disposal