File List:
00 0301 051 0.pdf
00 0302 618 6.pdf
00 0303 482 0.pdf
Pre-delivery inspection.pdf
00 0301 051 0.pdf:
PROFI CAM 3
Table of contents
1 Introduction
1.1 Notes on the manual
1.1.1 Validity of manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.1.4 Optional equipment
1.1.5 Qualified specialist workshop
1.1.6 Maintenance information
1.1.7 Warranty notes
1.1.8 Spare parts and technical questions
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2.1 Identifying warnings
2.1.1 Hazard signs
2.1.2 Signal word
2.2 Safety rules
2.2.1 Meaning of Operator’s Manual
2.2.2 Observing safety decals and warnings
2.2.3 Optional equipment and spare parts
3 Product description
3.1 Overview and method of operation
3.1.1 How the PROFI CAM works
3.2 Identification plates and identification number
3.2.1 Position of identification plates
3.2.2 Explanation of PROFI CAM identification plate
3.3 Information on the product
3.3.1 CE marking
4 Operating and control elements
4.1 Camera system
4.1.1 Camera system monitor
4.2 Menu structure
4.2.1 Main menu
4.2.2
4.2.3
4.2.4
4.2.5
4.2.6
5 Technical specifications
5.1 PROFI CAM
5.1.1 Monitor
5.1.2 Camera
5.1.3 Switch box
5.1.4 Degree of protection against foreign bodies and water
6 Preparing the product
6.1 Shutting down and securing the machine
6.1.1 Switching off and securing the machine
6.2 Prior to operation
6.2.1 Carry out prior to operation
6.2.2 Installing the sun protection
6.2.3 Aligning the camera
6.2.4 Connecting the camera electrics
7 Operation
7.1 Monitor
7.1.1 Switching on the monitor
7.1.2 Calling up the menu
7.1.3 Setting a menu item
7.1.4 Setting the image orientation
7.1.5 Setting automatic screen darkening
7.1.6 Image mirroring
7.1.7 Setting the trigger view
7.1.8 Setting the follow-up time for trigger view
7.1.9 Setting the display mode
7.1.10 Activating/deactivating a display mode
8 Faults and remedies
8.1 Electrical and electronic system
8.1.1 Overview of problems on PROFI CAM camera system
8.1.2 Replacing the switch box fuse
9 Maintenance
9.1 Maintenance intervals
9.1.1 Every 10 operating hours or daily
9.2 Camera system
9.2.1 Checking the camera system for dirt
9.2.2 Cleaning the camera
9.2.3 Cleaning the switch box
9.2.4 Cleaning the monitor
10 Placing out of operation and disposal
10.1 General Information
10.1.1 Putting out of operation and disposal
11 Technical terms and abbreviations
11.1 Abbreviations
11.1.1 Units
11.1.2 Abbreviations
11.1.3 Technical terms
00 0302 618 6.pdf:
CONVIO FLEX / CONVIO 1380CONVIO FLEX / CONVIO 1230CONVIO FLEX / CONVIO 1080CONVIO FLEX / CONVIO 930CONVIO FLEX / CONVIO 770
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.1.4 Optional equipment
1.1.5 Qualified specialist workshop
1.1.6 Maintenance notes
1.1.7 Warranty notes
1.1.8 Spare parts and technical questions
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2.1 Identifying warnings
2.1.1 Hazard signs
2.1.2 Signal word
2.2 Safety rules
2.2.1 Importance of Operator’s Manual
2.2.2 Observing safety decals and warnings
2.2.3 Requirements for all persons working with the machine
2.2.4 Hazard areas
2.2.5 Standing between machine and front attachment
2.2.6 Persons riding on the machine
2.2.7 Fitting a front attachment or hitching a transport trailer to the machine
2.2.8 Danger of injury from rotating shafts
2.2.9 Structural alterations
2.2.10 Optional equipment and spare parts
2.2.11 Operation only following proper putting into operation
2.2.12 Technical condition
2.2.13 Danger from damage to the machine
2.2.14 Keeping safety devices functional
2.2.15 Personal protective equipment
2.2.16 Wearing suitable clothing
2.2.17 Removing dirt and loose objects
2.2.18 Preparing the machine for road travel
2.2.19 Unsuitable operating utilities
2.2.20 Safe handling of operating and auxiliary utilities
2.2.21 Environmental protection and disposal
2.2.22 Electrocution by electrical system
2.2.23 Pressurised fluids
2.2.24 Working on machine only after shutting it down
2.2.25 Maintenance operations and repair work
2.2.26 Raised machine parts and loads
2.2.27 Hazard from welding work
2.3 Safety decals on the machine
2.3.1 Structure of safety decals
2.3.2 Position of safety decals
Safety decals on the front attachment
00 0516 453 1
00 0516 414 0
00 0516 414 0
00 0516 401 0
00 0515 134 0
00 0114 052 0
00 0514 038 2
00 0516 525 0
00 0515 209 1
00 0516 063 0
00 2674 085 0
00 2674 085 0
00 2674 085 0
Warning sign on LASER PILOT* bracket
00 0515 380 0
Warning sign on rapeseed separating knife*
00 0515 209 1
00 0514 878 0
00 0516 401 0
3 Machine description
3.1 Overview and method of operation
3.1.1 Overview of the CONVIO FLEX/CONVIO
3.1.2 Storing the Operator’s Manual
3.1.3 Function of CONVIO FLEX / CONVIO
CONVIO FLEX
CONVIO FLEX / CONVIO with rapeseed equipment*
3.1.4 How the reel tractive effort function works
3.1.5 How the conveyor belts work
3.1.6 How the flexible finger bar works
Balancing pressure of the finger bar
Cleaning function
3.1.7 Functions of the overload protection features
3.1.8 How the feed augers* work
3.1.9 Function of stabilizer wheels*
3.2 Optional machine equipment
3.2.1 Feed augers
3.2.2 Speed kit for the reel
3.2.3 Speed kit for the intake auger
3.2.4 Speed kit for the knife
3.2.5 Rear panel raiser
3.2.6 Stone protection
3.2.7 Cover plate
3.2.8 Extension of outer deflectors
3.2.9 Grain sensor band for CONVIO FLEX
3.2.10 Wear skids for CONVIO
3.2.11 Stabilizer wheels
3.2.12 Rapeseed separating knife
3.2.13 Transport box for rape cutting equipment
3.2.14 Lighting
3.3 Identification plates and identification numbers
3.3.1 Identification plate of front attachment
3.4 Information on the machine
3.4.1 Decal
4 Operating and display elements
4.1 Front attachment
4.1.1 Controls
5 Technical specifications
5.1 CONVIO FLEX / CONVIO
5.1.1 Compatible machines
5.1.2 Dimensions
5.1.3 Weights
5.1.4 Weights
5.1.5 Reel
5.1.6 Mower unit
5.1.7 Tyre pressure
5.2 Operating utilities
5.2.1 Lubricants
5.2.2 Hydraulic oil
6 Machine preparation
6.1 Switching off and securing the machine
6.1.1 Switching off and securing the machine
6.2 Loading the front attachment
6.2.1 Loading and lashing down the front attachment
6.3 Mounting the front attachment
6.3.1 Installing the front attachment
6.3.2 Identifying the hydraulic oil
6.3.3 Preparing the locking
6.3.4 Suspending the front attachment
6.3.5 Locking the front attachment
6.3.6 Installing the universal drive shaft
6.3.7 Mounting the multi-coupler
6.4 Removing the front attachment
6.4.1 Removing the front attachment
6.4.2 Removing the multi-coupler
6.4.3 Removing the universal drive shaft
6.4.4 Unlocking the front attachment
6.4.5 Unhinging the front attachment
6.5 Crop feeding
6.5.1 Applying and releasing the reel safety locks
6.6 Mower unit
6.6.1 Fitting the finger bar safety device
7 Operation
7.1 Driving the machine
7.1.1 Preparing road travel
7.1.2 Adjusting the parking position
Adjusting the parking position automatically
7.1.3 Overview of the transport trailer support
Position of the swivelling supports
Inner swivelling supports
Outer swivelling supports
7.1.4 Preparing the transport trailer for road travel
7.2 Fieldwork
7.2.1 Preparing fieldwork
7.2.2 Adjusting the working position
7.2.3 Setting the operational mode of the CONVIO FLEX
7.2.4 Checking the crop pick-up
7.3 Grain harvest
7.3.1 Adjusting the front attachment for grain harvest
7.3.2 Fitting the AUTO CONTOUR* sensing bands
7.4 Soybean harvest
7.4.1 Setting up the front attachment for soybean harvesting
7.4.2 Adjusting the cutting height for harvesting soybeans
7.4.3 Removing the AUTO CONTOUR* sensing bands
7.5 Rape harvest
7.5.1 Installing the rapeseed equipment*
7.5.2 Fitting the rapeseed separating knife*
7.5.3 Removing the rapeseed separating knife*
7.5.4 Installing the rape plate*
7.6 Electric and electronic system
7.6.1 Switching the lighting equipment* on and off
Controlling the lighting equipment on the front attachment
Controlling the lighting equipment from the cab
7.7 Chassis
7.7.1 Adjusting the stabiliser wheels*
7.7.2 Folding the stabiliser wheel* in and out
Folding in the stabiliser wheel
Folding out the stabiliser wheel
7.8 Steering
7.8.1 Folding out the LASER PILOT*
7.9 Crop feeding
7.9.1 Operating the reel tractive effort function
7.9.2 Adjusting the control arm
7.9.3 Overview of crop dividers
7.9.4 Removing the soybean crop divider
7.9.5 Fitting the soybean crop divider
7.9.6 Adjusting the soybean crop divider
7.9.7 Fitting the divider points
7.9.8 Removing the divider points
7.9.9 Installing the crop divider extension*
7.9.10 Removing the crop divider extension*
7.9.11 Removing and fitting the crop divider support
7.9.12 Fitting the grain crop divider
7.9.13 Removing the grain crop divider
7.9.14 Fitting and removing the outer deflector
Installing the outer deflector
Removing the outer deflector
7.9.15 Fitting and removing the feed plate
7.9.16 Adjusting the long crop dividers
7.9.17 Folding out the long crop dividers
7.9.18 Folding in the long crop dividers
7.9.19 Adjust the short crop dividers.
7.9.20 Folding out the short crop dividers
7.9.21 Folding in the short crop dividers
7.9.22 Adjusting the reel tines
7.9.23 Adjusting the reel tines
7.9.24 Installing the cover plate*
7.10 Belt conveyor
7.10.1 Adjusting the speed of the conveyor belts
7.10.2 Setting slip monitoring of the conveyor belts
7.10.3 Reversing the conveyor belts
7.11 Intake auger
7.11.1 Switching the feed augers* on and off
7.11.2 Adjusting the feed auger* position
Adjusting the feed auger
Changing the setting range
7.11.3 Adjusting the intake auger fingers
7.11.4 Changing the intake auger speed
7.11.5 Removing the auger plate extension
7.11.6 Removing the baffle plates*
7.12 Mower unit
7.12.1 Adjusting the balancing pressure of the flexible finger bar
Setting the balancing pressure in the CEBIS menu
Adjusting the balancing pressure on the front attachment
7.12.2 Activating the rapeseed separating knives*
7.12.3 Activating the rapeseed separating knives*
7.12.4 Fitting and removing the crop lifter*
Installing crop lifters
Removing the crop lifter
7.12.5 Changing the cutting frequency
7.12.6 Adjusting knives so that they move in opposite directions
Checking that the knives are moving in opposite directions
Adjusting knives so that they move in opposite directions
8 Faults and remedies
8.1 Front attachment
8.1.1 Improving crop flow
8.1.2 Reducing grain losses
8.1.3 Crop feeding
8.1.4 Conveyor belts
8.1.5 Intake auger
8.1.6 Mower unit
8.1.7 Ground guidance
8.2 Hydraulic system
8.2.1 Bleeding the reel hydraulic cylinders
8.3 Electric and electronic system
8.3.1 Preparing welding work
8.4 Crop feeding
8.4.1 Checking the basic settings of the reel
Basic reel adjustment
Checking the reel position
Checking the reel height
8.4.2 Checking the basic settings of the reel
Basic reel adjustment
Checking the reel position
Checking the reel height
8.4.3 Replacing the reel tines
8.5 Belt conveyor
8.5.1 Changing the side conveyor belts
8.5.2 Changing the centre conveyor belt
Opening the cover
Removing the deflecting roller
Removing the cross member
Removing the drive shaft
Fitting the deflecting roller
Fitting the cross member
Fitting the drive shaft
Closing the cover
8.6 Intake auger
8.6.1 Changing the intake auger fingers (without tools)
8.6.2 Changing the intake auger fingers
8.6.3 Removing the dust shield plate
9 Maintenance
9.1 Preparing maintenance
9.1.1 Opening and closing the side panels
Opening the front side panel
Closing the front side panel
Removing the rear side panel
Fitting the rear side panel
9.1.2 Opening and closing the cover
Opening the cover
Closing the cover
9.1.3 Opening and closing the cover
Opening the cover
Closing the cover
9.2 Maintenance intervals
9.2.1 Before the harvest
9.2.2 After the first 50 operating hours
9.2.3 Daily
9.2.4 Every 50 operating hours
9.2.5 Every 100 operating hours
9.2.6 Every 250 operating hours
9.2.7 Every 500 operating hours
9.2.8 Every 1000 operating hours
9.2.9 After the harvest
9.2.10 Preserving the front attachment
9.3 Lubrication chart
9.3.1 Grease the grease points to be covered every 50 working hours
Applies to: MONTANA
9.3.2 Grease the grease points every 100 operating hours
CONVIO FLEX
9.3.3 Grease the grease points every 250 operating hours
9.4 Transmission, clutch and driveshaft
9.4.1 Checking the oil level in the transfer gearbox (G01)
9.4.2 Changing the oil in the transfer gearbox (G01)
Draining the oil
Topping up oil
9.4.3 Checking the oil level of angle drives (G02) and (G03)
9.4.4 Changing the oil of angle drives (G02) and (G03)
Draining the oil
Topping up oil
9.5 Chassis
9.5.1 Checking the wheel hub bearing play
9.5.2 Adjusting the wheel hub bearing play
9.5.3 Checking the tightening torque of wheel nuts
9.6 Drives
9.6.1 Adjusting the drives
9.6.2 Setting the reel drive chain (K01)
9.7 Hydraulic system
9.7.1 Checking the hydraulic oil level
9.7.2 Changing the hydraulic oil, return filter and fresh air filter element
Draining the hydraulic oil
Changing the return filter
Changing the fresh air filter element
Topping up the hydraulic oil
9.7.3 Checking the hydraulic hoses
Marking of hydraulic hoses
9.8 Belt conveyor
9.8.1 Cleaning the conveyor belts
Cleaning the side conveyor belts
Cleaning the centre conveyor belt
9.8.2 Adjusting the tension of the side conveyor belts
9.8.3 Adjusting the tension of the centre conveyor belt
9.8.4 Removing the strip seals
9.8.5 Removing the strip seals
9.8.6 Checking the cover seals
Aligning the outer cover seals
Aligning the inner cover seals
Adjusting the cover pre-load
9.9 Mower unit
9.9.1 Changing the knives
9.9.2 Changing the segmented knife
Installing the knife connection
Assembling cutterbar sections (A) with reinforcing plate
Assembling cutterbar sections (B) without reinforcing plate
Fitting the overlapping segment
9.9.3 Checking the crop guards*
Checking the low hold-down clips
Checking the wear plate
Check wear of high hold-down clip
Checking the high hold-down clip
9.9.4 Checking the crop guards*
Checking the low hold-down clips
Checking the wear plate
Check wear of high hold-down clip
Checking the high hold-down clip
9.9.5 Checking the upper fingers*
Checking the upper fingers
Checking the wear plate
Check wear of high hold-down clip
Checking the high hold-down clip
9.9.6 Replacing the short double fingers
9.9.7 Replacing the split double fingers
9.9.8 Replacing the long double fingers
9.9.9 Aligning the double fingers
9.9.10 Replacing the knife section
9.9.11 Changing the knives of the rapeseed separating knives*
Removing the knives
Installing the knives
9.9.12 Cleaning the guide straps of the rapeseed separating knives*
9.10 Ground guidance
9.10.1 Replacing the wear skids
10 Putting out of operation and disposal
10.1 Putting out of operation and disposal
10.1.1 Decommissioning and disposal
11 Declaration of Conformity
11.1 CONVIO FLEX / CONVIO
11.1.1 EC declaration of conformity
11.1.2 EC declaration of conformity
11.1.3 UK Declaration of Conformity
11.1.4 UK Declaration of Conformity
00 0303 482 0.pdf:
PROFI CAM 4
Table of contents
1 Introduction
1.1 Notes on the manual
1.1.1 Validity of manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.1.4 Optional equipment
1.1.5 Qualified specialist workshop
1.1.6 Maintenance information
1.1.7 Notes on warranty
1.1.8 Spare parts and technical questions
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2.1 Identifying warnings
2.1.1 Hazard signs
2.1.2 Signal word
2.2 Safety rules
2.2.1 Meaning of Operator’s Manual
2.2.2 Structural changes
2.2.3 Optional equipment and spare parts
2.2.4 Operation only following proper putting into operation
2.2.5 Technical status
2.2.6 Respecting technical limit values
Respecting technical limit values
2.2.7 Hazards when driving on roads and fields
3 Product description
3.1 Overview and method of operation
3.1.1 How the PROFI CAM works
3.2 Identification plates and identification number
3.2.1 Identification plates
3.3 Information on the product
3.3.1 CE marking
4 Operating and display elements
4.1 Camera system
4.1.1 Camera system monitor
4.1.2 CEBIS
4.2 Menu structure
4.2.1 Main menu
4.2.2
4.2.3
4.2.4
4.2.5
4.2.6
5 Technical specifications
5.1 PROFI CAM
5.1.1 Monitor
5.1.2 Camera
5.1.3 Switch box
6 Preparing the product
6.1 Switching off and securing the machine
6.1.1 Switching off and securing the machine
6.2 Prior to putting into operation
6.2.1 Carry out prior to operation
6.2.2 Installing the sun protection
6.2.3 Aligning the camera
7 Operation
7.1 Monitor
7.1.1 Switching on the monitor
7.1.2 Calling up the menu
7.1.3 Setting a menu item
7.1.4 Setting the image orientation
7.1.5 Setting automatic screen darkening
7.1.6 Image mirroring
7.1.7 Setting the trigger view
7.1.8 Setting the follow-up time for trigger view
7.1.9 Setting the display mode
7.1.10 Activating/deactivating a display mode
8 Faults and remedies
8.1 Electric and electronic system
8.1.1 Overview of problems on PROFI CAM camera system
9 Maintenance
9.1 Maintenance intervals
9.1.1 Every 10 operating hours or daily
9.2 Camera system
9.2.1 Checking the camera system for dirt
9.2.2 Cleaning the camera
9.2.3 Cleaning the switch box
9.2.4 Cleaning the monitor
10 Putting out of operation and disposal
10.1 General information
10.1.1 Putting out of operation and disposal
11 Technical terms and abbreviations
11.1 Abbreviations
11.1.1 Units
11.1.2 Abbreviations
11.1.3 Technical terms
Pre-delivery inspection.pdf:
CONVIO FLEX / CONVIO 1380CONVIO FLEX / CONVIO 1230CONVIO FLEX / CONVIO 1080CONVIO FLEX / CONVIO 930CONVIO FLEX / CONVIO 770
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of manual
1.1.2 Symbols and notes
1.2 Identification plates and identification numbers
1.2.1 Identification plate of front attachment
1.3 Operator��s Manual
1.3.1 Storing the Operator’s Manual
2.1 Identifying warnings
2.1.1 Hazard signs
2.1.2 Signal word
2.2 Safety rules
2.2.1 Importance of Operator’s Manual
2.2.2 Observing safety decals and warnings
2.2.3 Requirements for all persons working with the machine
2.2.4 Hazard areas
2.2.5 Standing between machine and front attachment
2.2.6 Persons riding on the machine
2.2.7 Fitting a front attachment or hitching a transport trailer to the machine
2.2.8 Danger of injury from rotating shafts
2.2.9 Structural alterations
2.2.10 Optional equipment and spare parts
2.2.11 Operation onl following proper putting into operation
2.2.12 Technical condition
2.2.13 Danger from damage to the machine
2.2.14 Keeping safety devices functional
2.2.15 Personal protective equipment
2.2.16 Wearing suitable clothing
2.2.17 Rng dirt and loose objects
2.2.18 Preparing the machine for road trav 2.2.19 Unsuitable operating utilities
2.2.20 Safe handling of operating and auxiliary utilities
2.2.21 Environmental protection and disposal
2.2.22 Electrocution by electrical system
2.2.23 Pressurised fluids
2.2.24 Working on machine only after shutting it down
2.2.25 Maintenance operations and repair work
2.2.26 Raised machine parts and loads
2.2.27 Hazard from welding work
2.3 Safety decals on the machine
2.3.1 Structure of safety decals
2.3.2 Position of safety decals
Safety decals on the front attachment
00 0516 453 1
00 0516 414 0
00 0516 414 0
00 0516 401 0
00 0515 134 0
00 0114 052 0
00 0514 038 2
00 0516 525 0
00 0515 209 1
00 0516 063 0
00 2674 085 0
00 2674 085 0
00 2674 085 0
Warning sign on LASER PILOT* bracket
00 0515 380 0
Warning sign on rapeseed separating knife*
00 0515 209 1
00 0514 878 0
00 0516 401 0
3 Technical specifications
3.1 CONVIO FLEX / CONVIO
3.1.1 Dimensions
3.1.2 Weights
3.1.3 Weights
3.1.4 Tyre pressure
3.2 Operating utilities
3.2.1 Lubricants
3.2.2 Hydraulic oil
4 Machine preparation
4.1 Loading the front attachment
4.1.1 Loading and lashing down the front attachment
4.2 Prior to putting into operation
4.2.1 Prior to initial operation
4.2.2 Removing the transport safety equipment of the finger bar
Overview of transport safety equipment on the finger bar
Removing the transport safety equipment from the finger bar
Fitting the transport safety equipment on the carrier arms
4.2.3 Removing the transport safety equipment of the reel and of the control arms
Removing the lift eyes
Removing the reel transport safety equipment
Removing the transport safety equipment of control arms
4.2.4 Removing transport equipment
Removing the pallet*
Removing the transport supports
4.2.5 Adjusting the reel
Checking the reel
Turning the reel
4.2.6 Assembling the reel
Attaching the hydraulic cylinders at the outer reel arms
Attaching the potentiometer on the left reel arm
Hooking the hydraulic cylinder into the middle reel support arm
Fitting the tine tube
Fitting the plate
4.2.7 Removing the transport safety retainer of the hydraulic oil tank
4.2.8 Installing the LASER PILOT*
4.2.9 Adjusting the feed auger* position
Adjusting the feed auger
Changing the setting range
4.2.10 Checking the tightening torque of wheel nuts
4.2.11 Checking the hydraulic system of stabiliser wheels*
Filling the hydraulic system of the stabiliser wheels
Preparing for filling
Preparing for bleeding
4.2.12 Fitting a rear panel raiser*
4.2.13 Installing the universal drive shaft bracket
4.2.14 Fitting the soybean crop divider
4.2.15 Fitting the grain crop divider
4.2.16 Bleeding the reel hydraulic cylinders
4.2.17 Checking the basic settings of the reel
Basic reel adjustment
Checking the reel position
Checking the reel height
4.2.18 Checking the basic settings of the reel
Basic reel adjustment
Checking the reel position
Checking the reel height
4.2.19 Adjusting knives so that they move in opposite directions
Checking that the knives are moving in opposite directions
Adjusting knives so that they move in opposite directions
4.2.20 Checking the oil level in the transfer gearbox (G01)
4.2.21 Checking the oil level of angle drives (G02) and (G03)
4.2.22 Checking the hydraulic oil level
4.2.23 Adjusting the tension of the side conveyor belts
4.2.24 Adjusting the tension of the centre conveyor belt
4.2.25 Installing the switch for the left-hand rapeseed separating knife*
4.3 Chassis
4.3.1 Overview of the transport trailer support
Position of the swivelling supports
Inner swivelling supports
Outer swivelling supports
4.3.2 Adjusting the transport trailer supports
4.3.3 Visibility improvement*
4.3.4 Fitting the visibility kit* for CONVIO FLEX / CONVIO
Installing the indicator on the front attachment
Installing the indicator on the front attachment
Installing the console on the transport trailer
Installing the console on the transport trailer
4.3.5 Fitting the visibility kit* for CONVIO FLEX / CONVIO
Installing the indicator on the front attachment
Installing the console on the transport trailer
Claas Operator Manual PDF
Claas Operator Manual PDF
Claas RANGER 975-964, 970, 960 und PLUS (516) Telehandlers Operator Manual DE
![](https://automanual.net/wp-content/uploads/2024/04/claas-convio-1380-770-590-combines-operator-manual-en-1.jpg)