Claas Corto 275 F Profil (655) Mower Operator Manual EN

File List:

00 0293 507 4.pdf
00 2348 408 0.pdf
00 2348 427 0.pdf

00 0293 507 4.pdf:

1 Machine description
2 Introduction
Introduction
Validity
3 Table of contents
4 Preface
Of special importance
Identification plate
5 Safety Rules
Intended use
Avoidable incorrect applications
De-commissioning and disposal
Identification of warning and danger signs
General safety regulations and safety precautions
Attached machines
Trailed machines
PTO operation
Hydraulic system
Maintenance
Noise pressure level
Safety decals with pictorials
6 Technical data
CORTO 3150 F Profil
CORTO 275 F Profil
Axial loading, minimum ballast and total weight calculation
Noise level
CORTO 3150 F Profil
CORTO 275 F Profil
7 Assembly
Unloading/loading the machine
Assembling the machine.
CORTO 3150 F
CORTO 275 F
Adjusting the universal shaft support
Mounting the mower blades
CORTO 3150F/275F
First machine hitch-up
8 Before operation
Check every time before operation
Hitch up the mower
Three-point hitching with quick coupler
Longitudinal compensation of mower
Adjusting the top link
Universal drive shaft
Mounting universal drive shaft
Fitting to DISCO 8550 / 8550 C
Fitting on CLAAS Celtis
Permissible drive shaft angles
Adapting the length
Weight relief
Fitting examples
Parking the machine
Before transport
Road travel
Lighting bracket
9 Operation
Field operation
Working position
Transport position
Adjusting the working height
Adjusting the cutting height for uneven terrain
Weight relief
Adjusting the swath width
Putting the mower into operation
Notes on mowing
Environmental recommendations
Difficult working conditions
Accessory equipment
Skid plate extension for high cut
Slip yoke kit
Additional swath discs
Three-point booster
Mounting with lateral offset
Longitudinal swinging mechanism
10 Maintenance
Important maintenance instructions
Screws and bolts
Hydraulic system
Lubrication
Protective devices (guard frames)
Gear lubrication
Gear casing
Main gearbox
Checking the V-belts
Tensioning the V-belts
Replacing the V-belts
Adjusting the cutting height
Mower blades
Replacing the mower blades
Mower blade holders
Spring adjustments
Longitudinal mower compensation
Adjusting the longitudinal compensation springs
Transverse compensation of mowing unit
Readjusting the transverse compensation
Swath adjustment
Universal drive shaft
General notes on universal drive shafts
Protective devices
Threaded fasteners
Fasteners
Cleaning and care
Winter storage
11 Lubricating chart
Safety Rules
Lubricants
Lubrication

00 2348 408 0.pdf:

CEMIS 100
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of the manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2 Safety
2.1 Safety rules
2.1.1 General safety and accident prevention regulations
2.1.2 Interaction between terminal and machine or tractor
2.1.3 Electrocution by electrical system
3 Product description
3.1 Overview and method of operation
3.1.1 Overview of CEMIS 100
3.1.2 Function principle of CEMIS 100
3.2 Identification plates and identification numbers
3.2.1 Spare parts and technical questions
3.2.2 Identification plate of CEMIS 100
4 Operating and display elements
4.1 CEMIS 100
4.1.1 User interface for LINER
4.1.2 User interface for ROLLANT
4.1.3 User interface for UNIWRAP
5 Technical specifications
5.1 CEMIS 100
5.1.1 Specification
6 Operation
6.1 CEMIS 100
6.1.1 Operating the CEMIS 100
6.1.2 Switching CEMIS 100 on
6.1.3 Switching CEMIS 100 off
7 Maintenance
7.1 CEMIS 100
7.1.1 Daily
8 Putting out of operation and disposal
8.1 General information
8.1.1 Removal from service and disposal
9 Technical terms and abbreviations
9.1 Terms and explanations
9.1.1 Technical words
9.1.2 Abbreviations

00 2348 427 0.pdf:

CEMIS 700
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of the manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2 Safety
2.1 Safety rules
2.1.1 General safety and accident prevention regulations
2.1.2 Interaction between terminal and machine or tractor
2.1.3 Electrocution by electrical system
3 Product description
3.1 Overview and method of operation
3.1.1 Overview of CEMIS 700
3.1.2 Function principle of CEMIS 700
3.2 Identification plates and identification numbers
3.2.1 Spare parts and technical questions
3.2.2 Identification plate of CEMIS 700
4 Information on the product
4.1 Software version
5 Operating and display elements
5.1 CEMIS 700
5.1.1 User interface
5.1.2 Terminal program
6 Technical specifications
6.1 CEMIS 700
6.1.1 Specification
7 Operation
7.1 CEMIS 700
7.1.1 Operating the CEMIS 700
7.1.2 Switching CEMIS 700 on
7.1.3 Switching CEMIS 700 off
7.2 Terminal settings
7.2.1 Making settings
Making settings with the rotary button
Making settings with the touch function
7.2.2 Setting the screen lighting
Daytime mode
Nighttime mode
Activating automatic key lighting
7.2.3 Setting the time and date
7.2.4 Displaying diagnosis information
On-board power supply voltage display
Display of CLAAS ISOBUS ECU address and name
7.2.5 Setting the language and display formats
Setting the language
Setting display formats
7.2.6 Setting the volume
7.2.7 Deleting an ISOBUS implement
8 Maintenance
8.1 Maintenance
8.1.1 Daily
9 Putting out of operation and disposal
9.1 General information
9.1.1 Removal from service and disposal
10 Technical terms and abbreviations
10.1 Terms and explanations
10.1.1 Technical words
10.1.2 Abbreviations