Claas Corto 3100 (644) Mower Operator Manual EN

File List:

00 0294 689 5.pdf
00 2348 408 0.pdf
00 2348 427 0.pdf

00 0294 689 5.pdf:

1 Introduction
Introduction
Validity
2 Contents
3 Preface
Of special importance
Identification plate
4 Safety rules
Intended use
Identification of warning and danger signs
General safety and accident prevention instructions
Attached machines
Attached devices
PTO Operation
Hydraulic system
Maintenance
Sound pressure level
Safety decals with pictorials
5 Specifications
Axle loads, minimum ballast and total weight calculation
Calculating the minimum ballast front
Calculating the minimum ballast rear
Calculating the actual front axle load
Calculating the actual total weight
Calculating the actual rear axle load
Tyre carrying capacity
Noise level
6 Assembly
Assembly CORTO 3100 NC
Fitting cutting blades
Conditioner
Fitting the conditioner
Removing the conditioner
Fitting the cover
7 Prior to operation
Check every time prior to operation
Hitching up
Hitch pin
Adjusting the universal drive shaft
Adapting the length
Mounting the universal drive shaft
Wide angle equal running linkage
Hydraulics
Electrics
Prop stand
Fitting the machine
Prior to transportation
Driving on public roads
Transport security:
8 Operation
Operation
Working position
Conditioner
Unloading the machine
Setting values
Cut height adjustment
Changing the swath width:
Feeder aids
Recommendations for environmental protection
Optional equipment
Skid plate extensions for high cutting C03 0010
Spacer cone for high cutting C03 0040
Domed mower blades
Reinforced mower blades
Feeder slleving of middle drums E03 0020
Hydraulic connection parts for tractors R03 0030
Fitting kit Sealing and Feeder Aid
Fitting kit Additional Chicane
9 Maintenance
Important maintenance instructions
Hydraulic system
Energy accumulators
Lubrication
Drive systems
Tensioning the drive belts
Belt tension main drive
Belt tension – conditioner drive
Gearbox and gear casing
main gearbox
Oil filling quantities:
Checking the oil level:
Oil change:
Angle drive
Oil filling volume:
Checking the oil level:
Oil change:
Gear casing
Oil filling volume:
Checking the oil level:
Oil change:
Mower blades
Changing the mower blades
Mower blade holders
Cut height adjustment
Hydraulics
Hydraulic hoses
Universal drive shaft
Disc clutch maintenance
Bolted connections
Fasteners
End of season storage
10 Lubrication chart
Safety rules
Lubricants
Lubrication

00 2348 408 0.pdf:

CEMIS 100
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of the manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2 Safety
2.1 Safety rules
2.1.1 General safety and accident prevention regulations
2.1.2 Interaction between terminal and machine or tractor
2.1.3 Electrocution by electrical system
3 Product description
3.1 Overview and method of operation
3.1.1 Overview of CEMIS 100
3.1.2 Function principle of CEMIS 100
3.2 Identification plates and identification numbers
3.2.1 Spare parts and technical questions
3.2.2 Identification plate of CEMIS 100
4 Operating and display elements
4.1 CEMIS 100
4.1.1 User interface for LINER
4.1.2 User interface for ROLLANT
4.1.3 User interface for UNIWRAP
5 Technical specifications
5.1 CEMIS 100
5.1.1 Specification
6 Operation
6.1 CEMIS 100
6.1.1 Operating the CEMIS 100
6.1.2 Switching CEMIS 100 on
6.1.3 Switching CEMIS 100 off
7 Maintenance
7.1 CEMIS 100
7.1.1 Daily
8 Putting out of operation and disposal
8.1 General information
8.1.1 Removal from service and disposal
9 Technical terms and abbreviations
9.1 Terms and explanations
9.1.1 Technical words
9.1.2 Abbreviations

00 2348 427 0.pdf:

CEMIS 700
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of the manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2 Safety
2.1 Safety rules
2.1.1 General safety and accident prevention regulations
2.1.2 Interaction between terminal and machine or tractor
2.1.3 Electrocution by electrical system
3 Product description
3.1 Overview and method of operation
3.1.1 Overview of CEMIS 700
3.1.2 Function principle of CEMIS 700
3.2 Identification plates and identification numbers
3.2.1 Spare parts and technical questions
3.2.2 Identification plate of CEMIS 700
4 Information on the product
4.1 Software version
5 Operating and display elements
5.1 CEMIS 700
5.1.1 User interface
5.1.2 Terminal program
6 Technical specifications
6.1 CEMIS 700
6.1.1 Specification
7 Operation
7.1 CEMIS 700
7.1.1 Operating the CEMIS 700
7.1.2 Switching CEMIS 700 on
7.1.3 Switching CEMIS 700 off
7.2 Terminal settings
7.2.1 Making settings
Making settings with the rotary button
Making settings with the touch function
7.2.2 Setting the screen lighting
Daytime mode
Nighttime mode
Activating automatic key lighting
7.2.3 Setting the time and date
7.2.4 Displaying diagnosis information
On-board power supply voltage display
Display of CLAAS ISOBUS ECU address and name
7.2.5 Setting the language and display formats
Setting the language
Setting display formats
7.2.6 Setting the volume
7.2.7 Deleting an ISOBUS implement
8 Maintenance
8.1 Maintenance
8.1.1 Daily
9 Putting out of operation and disposal
9.1 General information
9.1.1 Removal from service and disposal
10 Technical terms and abbreviations
10.1 Terms and explanations
10.1.1 Technical words
10.1.2 Abbreviations