Claas Disco 3050 3000 F Fc (651) Mower Operator Manual EN

File List:

00 0293 491 9.pdf
00 1329 399 0.pdf
00 2348 408 0.pdf
00 2348 427 0.pdf

00 0293 491 9.pdf:

1 Introduction
Introduction
Validity
2 Table of contents
3 Preface
Of special importance
Identification plate
4 Safety Rules
Intended use
Identification of warning and danger signs
General safety and accident prevention instructions
Attached machines
Attached devices
PTO Operation
Hydraulic system
Maintenance
Sound pressure level
Safety decals with pictorials
5 Specifications
DISCO 3050 F Plus DISCO 3050 F
DISCO 3050 FC Plus DISCO 3050 FC
DISCO 3000 FC
Calculating the axial loads, minimum ballast and total weight
Sound level from the DISCO 3050 FC PLUS / 3050 FC / 3050 F PLUS / 3050 F / 3000 FC Disc Mower
6 Prior to Operation
Loading and unloading machine
Fitting the blades
Mounting the deflector hood
Check and observe the following before putting into operation!
Mounting universal drive shaft
Fitting on CLAAS Celtis
Matching the universal drive shaft
Changing the direction of rotation
Attachment to the tractor
Setting the upper link
Weight relief
Fitting examples
Removing the machine
Prior to transportation
Driving on public roads
7 Operation
Operation
Working position
Setting the cutting height
High cut:
Low cut:
Ground adjustment
Safety equipment
Transport position
Changing the swathe width
DISCO 3050 FC Plus / 3050 FC / 3000 FC
DISCO 3050 F Plus / 3050 F
Conditioner
Changing the conditioner speed
Recommendations for environmental protection
Optional equipment
High cutting runners
Push-on runners
Kit for detachable forks
Wide deflector device DISCO 3050 FC Plus / 3050 FC / 3000 FC
Three point elevation
8 Maintenance
Important maintenance instructions
Lubrication
Guards (safety frame)
Drive systems
Tightening the conditioner drive belt
Mower head
Mower blades
Replacing mower blades
Mower blade box
Mower blade quick change system DISCO 3050 FC Plus / DISCO 3050 F Plus
Screwed mower blades DISCO 3050 FC / 3050 F / 3000 FC
Attaching mower blades
Mower discs
Replacing cutting discs
Arrangement of the pinion units
Fitting the pinion units
Conditioner tines
Fitting / removing the tines
Universal drive shaft
Maintenance of the disc coupling
Screw connections
Connecting elements
Care and cleaning
End of season storage
Malfunctions
9 Lubrication chart
Safety Rules
Lubricants
Lubrication

00 2348 408 0.pdf:

CEMIS 100
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of the manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2 Safety
2.1 Safety rules
2.1.1 General safety and accident prevention regulations
2.1.2 Interaction between terminal and machine or tractor
2.1.3 Electrocution by electrical system
3 Product description
3.1 Overview and method of operation
3.1.1 Overview of CEMIS 100
3.1.2 Function principle of CEMIS 100
3.2 Identification plates and identification numbers
3.2.1 Spare parts and technical questions
3.2.2 Identification plate of CEMIS 100
4 Operating and display elements
4.1 CEMIS 100
4.1.1 User interface for LINER
4.1.2 User interface for ROLLANT
4.1.3 User interface for UNIWRAP
5 Technical specifications
5.1 CEMIS 100
5.1.1 Specification
6 Operation
6.1 CEMIS 100
6.1.1 Operating the CEMIS 100
6.1.2 Switching CEMIS 100 on
6.1.3 Switching CEMIS 100 off
7 Maintenance
7.1 CEMIS 100
7.1.1 Daily
8 Putting out of operation and disposal
8.1 General information
8.1.1 Removal from service and disposal
9 Technical terms and abbreviations
9.1 Terms and explanations
9.1.1 Technical words
9.1.2 Abbreviations

00 2348 427 0.pdf:

CEMIS 700
Table of contents
1 Introduction
1.1 General information
1.1.1 Validity of the manual
1.1.2 Information about this Operator’s Manual
1.1.3 Symbols and notes
1.2 Intended use
1.2.1 Intended use
1.2.2 Reasonably foreseeable misuse
2 Safety
2.1 Safety rules
2.1.1 General safety and accident prevention regulations
2.1.2 Interaction between terminal and machine or tractor
2.1.3 Electrocution by electrical system
3 Product description
3.1 Overview and method of operation
3.1.1 Overview of CEMIS 700
3.1.2 Function principle of CEMIS 700
3.2 Identification plates and identification numbers
3.2.1 Spare parts and technical questions
3.2.2 Identification plate of CEMIS 700
4 Information on the product
4.1 Software version
5 Operating and display elements
5.1 CEMIS 700
5.1.1 User interface
5.1.2 Terminal program
6 Technical specifications
6.1 CEMIS 700
6.1.1 Specification
7 Operation
7.1 CEMIS 700
7.1.1 Operating the CEMIS 700
7.1.2 Switching CEMIS 700 on
7.1.3 Switching CEMIS 700 off
7.2 Terminal settings
7.2.1 Making settings
Making settings with the rotary button
Making settings with the touch function
7.2.2 Setting the screen lighting
Daytime mode
Nighttime mode
Activating automatic key lighting
7.2.3 Setting the time and date
7.2.4 Displaying diagnosis information
On-board power supply voltage display
Display of CLAAS ISOBUS ECU address and name
7.2.5 Setting the language and display formats
Setting the language
Setting display formats
7.2.6 Setting the volume
7.2.7 Deleting an ISOBUS implement
8 Maintenance
8.1 Maintenance
8.1.1 Daily
9 Putting out of operation and disposal
9.1 General information
9.1.1 Removal from service and disposal
10 Technical terms and abbreviations
10.1 Terms and explanations
10.1.1 Technical words
10.1.2 Abbreviations