Claas Quadrant 5200 (J31) Balers Assembly Instruction EN

File List:

00 0288 440 0.pdf
00 0290 143 2.pdf
00 0290 533 1.pdf
00 0292 437 0.pdf
00 0300 374 1.pdf
00 0302 001 0.pdf
00 0302 002 0.pdf
00 0304 376 1.pdf
00 1325 214 4.pdf

00 0288 440 0.pdf:

QUADRANT 5200
Table of contents
1 To this manual
1.1 General information
1.1.1 General points
1.1.2 Machines affected
2.1 General information
2.1.1 General points
2.1.2 Use in accordance with the original specifications
2.2 Safety instructions
2.2.1 Definition of hazard information
2.2.2 General safety and accident prevention advice
2.2.3 Parking the machine
3 Bill of material
3.1 Parts kit
3.1.1 Components of kit 1351 600 0
Front section of the hydraulic circuit
Intermediate section of the hydraulic circuit
Cylinder support on bale ramp
Octagon hydraulic circuit
Electrical wiring harness
Bale ejector
4 Mounting
4.1 Machine preparation
4.1.1 Securing the baler
4.1.2 Preparing the machine
Removing the accessories from the mechanical ramp
Preparing the hydraulic circuit
4.2 Fitting the kit
4.2.1 Fitting the front section of the hydraulic circuit
4.2.2 Fitting the intermediate section of the hydraulic circuit
4.2.3 Fitting the cylinder support onto the bale ramp
4.2.4 Fitting the octagon hydraulic circuit
4.2.5 Fitting the electrical wiring harness
4.2.6 Fitting the bale ejector
Removing the bale ramp
Fitting the bale ejector
Fitting the bale ramp

00 0290 533 1.pdf:

QUADRANT 5300QUADRANT 5200QUADRANT 4200
Table of contents
1 To this manual
1.1 General information
1.1.1 General points
1.1.2 Machines that can be equipped
2.1 General information
2.1.1 General points
2.1.2 Use in accordance with the original specifications
2.2 Safety instructions
2.2.1 Definition of hazard information
2.2.2 General safety and accident prevention advice
2.2.3 Parking the machine
3 Bill of material
3.1 Parts kit
3.1.1 Components of kit 00 1350 054 2
QUADRANT 5300 bale ramp kit with weighing device
3.1.2 Components of kit 00 1350 056 2
QUADRANT 5200 bale ramp kit with weighing device
3.1.3 Components of kit 00 1350 058 1
QUADRANT 4200 bale ramp kit with weighing device
4 Mounting
4.1 Machine preparation
4.1.1 Securing the baler
4.1.2 Removing the bale ramp
4.2 Fitting the kit
4.2.1 Fitting the bale ramp
4.2.2 Fit the roller lock
4.2.3 Electric wiring harnesses
Replacing the pressure regulation wiring harness
Connecting the weighing device wiring harness
4.2.4 Activation and start up

00 0302 001 0.pdf:

QUADRANT 5200
Table of contents
1 To this manual
1.1 General information
1.1.1 General points
1.1.2 Machines affected
2.1 General information
2.1.1 General points
2.1.2 Use in accordance with the original specifications
2.2 Safety instructions
2.2.1 Definition of hazard information
2.2.2 General safety and accident prevention advice
2.2.3 Parking the machine
3 Bill of material
3.1 Parts kit
3.1.1 Components of kit 1351 601 0
Intermediate section of the hydraulic circuit
Cylinder support on bale ramp
Octagon hydraulic circuit
Electrical wiring harness
Bale ejector
4 Mounting
4.1 Machine preparation
4.1.1 Securing the baler
4.1.2 Preparing the machine
Removing the accessories from the mechanical ramp
Preparing the hydraulic circuit
4.2 Fitting the kit
4.2.1 Fitting the intermediate section of the hydraulic circuit
4.2.2 Fitting the cylinder support onto the bale ramp
4.2.3 Fitting the octagon hydraulic circuit
4.2.4 Fitting the electrical wiring harness
4.2.5 Fitting the bale ejector
Removing the bale ramp
Fitting the bale ejector
Fitting the bale ramp

00 0302 002 0.pdf:

QUADRANT 5200
Table of contents
1 To this manual
1.1 General information
1.1.1 General points
1.1.2 Machines affected
2.1 General information
2.1.1 General points
2.1.2 Use in accordance with the original specifications
2.2 Safety instructions
2.2.1 Definition of hazard information
2.2.2 General safety and accident prevention advice
2.2.3 Parking the machine
3 Bill of material
3.1 Parts kit
3.1.1 Components of kit 00 1351 608 0
Intermediate section of the hydraulic circuit
Cylinder support on bale ramp
4 Mounting
4.1 Machine preparation
4.1.1 Securing the baler
4.1.2 Preparing the machine
Removing the accessories from the mechanical ramp
4.2 Fitting the kit
4.2.1 Fitting the intermediate section of the hydraulic circuit
4.2.2 Fitting the cylinder support onto the bale ramp
4.2.3 Fitting the electrical wiring harness