Claas ROLLANT 250 RC (725) Baler Technical System DE

File List:

– 00 0293 484 0.pdf
– 00 0293 485 0.pdf
– 00 0293 487 0.pdf

00 0293 484 0.pdf

Table of Content:
1 Hydraulic system technology ROLLANT 240/250/254/255
3 Chapter 1_x000B_Wiring diagram for overall hydraulics
3.1 1.1 Standard circuit diagram without Rolland multifunction valve
3.2 1.2 Circuit diagram standard with multifunction valve Rollant 2
3.3 1.3 Comfort circuit diagram without Rollant multifunction valve 2
3.4 1.4 Comfort circuit diagram with Rollant multifunction valve 25
3.5 1.5 Circuit diagram ROLLANT for UNIWRAP_x000B_ up to machine no. 72600130
3.6 1.6 Circuit diagram ROLLANT for UNIWRAP_x000B_ from machine no. 72600131
4 Chaultifunctional valve with pressure limitation ROLLANT 254, 25
4.6 2.6 Main valve block ROLLANT Comfort_x000B_ ROTOCUT, Pick-up, Roto
4.7 2.7 Circulation check valve, open/close tailgate with ROLLA
4.8 2.8 ROTOCUT knife ON/OFF with ROLLANT Standard
4.9 2.9 Lubricating oil pump
6 0293 484.0

00 0293 485 0.pdf

Table of Content:
1 Electric system technology ROLLANT 240/250
2 Structure of electrical circuit diagrams
4 central electrics
4.1 Central electrics Rollant 240/250 Standard
4.2 Central electrics Rollant 250 Comfort
4.3 UNIWRAP central electrics
5 Pin assignment of the modules
5.1 ROLLANT 240/250 Standard
5.2 ROLLANT 240/250 Comfort
5.3 UNIWRAP
6 Circuit diagram assignment of fuses and relays
7 circuit diagrams 01a – 40c
7.1 01a – Main power supply Rollant 240/250 Standard
7.2 01b – Main power supply Rollant 250 Comfort
7.3 01c – Main power supply Rollant 250 Comfort for UNIWRAP
7.4 01d – Main power supply UNIWRAP
7.5 04a – Circulation check valve (with central electrics) Rollant 250 Comfort
7.6 04b – Circulation check valve Rollant 250 Comfort for UNIWRAP
7.7 04c – UNIWRAP circulation check valve
7.8 05a – Terminal Rollant 250 Comfort
7.9 05b – Terminal UNIWRAP to mach. no. 726 00 130
7.10 06a – CAN bus, power supply module Rollant 240/250 Standard
7.11 06b – CAN bus, power supply module Rollant 250 Comfort
7.12 06c – CAN bus, power supply module Rollant 250 Comfort for UNIWRAP
7.13 06d – CAN bus, power supply module UNIWRAP up to mach. no. 72900130
7.14 06e – CAN bus, power supply module UNIWRAP from mach. no. 72900131
7.15 07a – Rotocut Rollant 240/250 Standard
7.16 07b – Rotocut Rollant 250 Comfort / Comfort for UNIWRAP
7.17 11a – Binding release Rollant 240/250 Standard
7.18 11b – Binding release Rollant 250 Comfort / Comfort for UNIWRAP
7.19 12a – Open / close tailgate Rollant 250 Comfort / Comfort for UNIWRAP
7.20 19a Loading / unloading bales UNIWRAP
7.21 20a – Raise and lower pick-up – Rollant 250 Comfort / Comfort for UNIWRAP
7.22 21a – Rotate wrapping arm – UNIWRAP
7.23 22a – Open/close film scissors, monitoring film tear – UNIWRAP
7.24 32a – Rear light, position light (with central electrics)
7.25 40a additional sockets
7.26 40b additional sockets
7.27 40c additional sockets
8 wire harnesses
8.1 Wiring harness A Part 1 (Rollant 250 Standard)
8.2 Wiring harness A Part 2 (Rollant 250 Standard)
8.3 Wiring harness B Part 1 (Rollant 250 Comfort / Rollant 250 Comfort for UNIWRAP)
8.4 Wiring harness B Part 2 (Rollant 250 Comfort / Rollant 250 Comfort for UNIWRAP)arness M (UNIWRAP)
10 0293 485.0

00 0293 487 0.pdf

Table of Content:
1 System technology diagnosis QUADRANT 2200
3 1.0 Service Menu Control Terminal (up to Module 1 No. 835023.2)
3.1 1.1 Structure of service menu
3.2 1.2 Additional information on page 1
3.3 1.3 Checking the inputs
3.4 1.4 Checking the outputs
3.5 1.5 Error display
3.6 1.6 Push button test
4 2.0 Service Menu Control Terminal (from module 1 no. 835023.3)
4.1 2.1 Structure of service menu
4.2 2.2 Additional information on page 1
4.3 2.3 Checking the inputs
4.4 2.4 Checking the outputs
4.5 2.5 Error display
4.6 2.6 Push button test
5 3.0 Sensor test
5.1 Foil sensor
5.2 Stop bar impulse
5.3 Wrapping arm impulse
5.4 Basic position
5.5 Changing table above
5.6 Bales on changing table
5.7 Bales in tipping trough
5.8 Tipping trough bottom
5.9 Tailgate closed
5.10 Tailgate open
5.11 Winding start signal
5.12 Binding start signal
6 4.0 Malfunction table
7 0293 487.0