IMT 60-85 CFM Hydraulic-Driven Rotary Screw Air Compressor Installation, Operation, Maintenance and Parts Manual 99905932 201602

Table of Content:

1 COVER
2 TABLE OF CONTENTS
3 SECTION 1: SAFETY
3.1 1.1 GENERAL INFORMATION
3.2 1.2 SUMMARY OF DANGERS, WARNINGS, CAUTIONS AND NOTES
3.3 1.3 DISPOSING OF MACHINE FLUIDS
4 SECTION 2: SPECIFICATIONS
4.1 TABLE 2A: SPECIFICATIONS
4.2 TABLE 2B: PRIME LUBRICANT CHARACTERISTICS
4.3 TABLE 2C: BOLT AND TORQUE SPECIFICATIONS
5 SECTION 3: INSTALLATION
5.1 3.1 MACHINE PACKAGE RECEIPT/INSPECTION
5.2 3.2 GENERAL INSTRUCTIONS
5.3 3.3 DETERMINING THE IMT CAS80R UNIT MOUNTING LOCATION
5.4 3.4 HYDRAULIC SYSTEM REQUIREMENTS
5.5 3.5 VENTILATION REQUIREMENTS
5.6 3.6 HYDRAULIC REQUIREMENTS
5.7 3.7 HYDRAULIC LINE SIZING
5.8 3.8 HYDRAULIC SYSTEM FILTRATION
5.9 3.9 HYDRAULIC OIL RESERVOIR
5.10 3.10 INSTALLATION
6 SECTION 4: OPERATION
6.1 4.1 GENERAL INFORMATION
6.2 4.2 PURPOSE OF CONTROLS
6.3 4.3 INITIAL START-UP PROCEDURE
6.4 4.4 ROUTINE START-UP PROCEDURE
6.5 4.5 COLD WEATHER START-UP PROCEDURE
6.6 4.6 ROUTINE SHUTDOWN PROCEDURE
6.7 4.7 OPERATING CONDITIONS
7 SECTION 5: MAINTENANCE
7.1 5.1 GENERAL INFORMATION
7.2 5.2 MACHINE MAINTENANCE SCHEDULE
7.3 5.3 REPLACEMENT PARTS
7.4 5.4 PARTS REPLACEMENT AND ADJUSTMENT PROCEDURES
8 SECTION 6: TROUBLESHOOTING
8.1 6.1 GENERAL INFORMATION
8.2 6.2 TROUBLESHOOTING GUIDE
9 SECTION 7: ILLUSTRATED PARTS LIST
9.1 7.1 PARTS ORDERING PROCEDURE
9.2 TABLE 7A: RECOMMENDED SPARE PARTS LIST
9.3 TABLE 7B: MAINTENANCE TRACKING LOG
9.4 7.2A COMPRESSOR ASSEMBLY AND REPLACEMENT PARTS
9.5 7.2B COMPRESSOR AND MOUNTING PARTS
9.6 7.3A HYDRAULIC MOTOR AND DRIVE – OPEN CENTER
9.7 7.3B CLOSED CENTER AND HYDRAULIC THERMAL VALVE
9.8 7.4 COOLING SYSTEM 12VDC / 24VDC
9.9 7.5 CONTROL SYSTEM
9.10 7.6 FRAME AND CANOPY – OVERALL ASSEMBLY
9.11 7.6A FRAME AND CANOPY – FRONT SIDE PANEL
9.12 7.6B FRAME AND CANOPY – ACCESS DOOR
9.13 7.6C FRAME AND CANOPY – ROOF PANEL
9.14 7.6D FRAME AND CANOPY – BACK SIDE PANEL
9.15 7.6E FRAME AND CANOPY – COMPRESSOR SIDE PANEL
9.16 7.6F FRAME AND CANOPY – HYDRAULIC DRIVE FRAME
9.17 7.7A CONTROL MANIFOLD – 12VDC / 24VDC OPEN CENTER
9.18 7.7B HYDRAULIC THERMAL VALVE – 12VDC / 24VDC
9.19 7.8 THERMAL CONTROL
9.20 7.9 DECAL LOCATIONS (PART 1 OF 2)
9.21 7.9 DECAL LOCATIONS (2 OF 2)
9.22 7.10 WIRING DIAGRAM
9.23 7.11 SCHEMATIC – HYDRAULIC OIL FLOW OPEN CENTER
9.24 7.12 SCHEMATIC – HYDRAULIC OIL FLOW OPEN CENTER, COLD WEATHER
9.25 7.13 SCHEMATIC – COMPRESSOR OIL/AIR FLOW (1 OF 2)
9.26 7.13 SCHEMATIC – COMPRESSOR OIL/AIR FLOW (2 OF 2)
9.27 7.14 HOSE AND TUBING – OPEN CENTER SYSTEM
9.28 7.15 HOSE AND TUBING – OPEN CENTER, COLD WEATHER SYSTEM
10 ADDRESS, PHONES AND WEB