IMT Model 3020 Crane Volume 2 – PARTS AND SPECIFICATIONS 9901196 Effective through 2007

Table of Content:

1 ELECTRONIC MANUALS
2 REVISIONS LIST
3 MANUAL EFFECTIVITY
4 INTRODUCTION
5 SPECIFICATIONS
5.1 GENERAL SPECIFICATIONS
5.2 PERFORMANCE CHARACTERISTICS
5.3 CYLINDERS
5.4 POWER SOURCE
5.5 ROTATION SYSTEM
5.6 CYLINDER HOLDING VALVES
5.7 EXCESSIVE LOAD LIMIT SYSTEM (ELLS)
5.8 WINCH
5.9 HYDRAULIC SYSTEM
5.10 MINIMUM CHASSIS SPECIFICATIONS
5.11 GEOMETRIC CONFIGURATION
5.12 CAPACITY CHART
6 CRANE REFERENCE
6.1 MAJOR CRANE ASSEMBLIES
6.2 WELDMENT PART NUMBER LOCATIONS
6.3 GREASE ZERK LOCATIONS & LUBRICANT REQUIREMENTS
6.4 RECOMMENDED SPARE PARTS LIST
6.5 INSTALLATION
6.6 CRANE INSTALLATION
6.7 HYDRAULIC INSTALLATION
6.8 CONTROL VALVE TROUBLESHOOTING
6.9 RELAY BOARD OPERATION
6.10 WINCH TROUBLESHOOTING
6.11 ANTI TWO-BLOCKING DEVICE
6.12 Excessive Load Limit System (ELLS) TEST PROCEDURE
6.13 ELLS TROUBLESHOOTING PROCEDURE
7 REPLACEMENT PARTS
7.1 PARTS INFORMATION
7.2 BASE ASM (41714695)
7.3 GEAR ROTATOR (71056543)
7.4 LOW PROFILE EXTENSION BOOM ASM. (41717133)
7.5 EXTENSION CYLINDER (3B210013)
7.6 LOW PROFILE LOWER BOOM ASM. – FROM 1/1/02 (41717138)
7.7 LOWER CYLINDER (3B212010)
7.8 WINCH/CABLE/HOOK KIT (31717067-1)
7.9 WINCH/CABLE/HOOK KIT (31717067-2)
7.10 WINCH (71057936)
7.11 CORD REEL ASM (51713168)
7.12 ELECTRICAL SCHEMATIC, PROP REMOTE CONTROL (99900855)
7.13 WIRE ROUTING (90714602)PROP’L RMT CTRL
7.14 CABLE ASM 14GA 2WIRE X 30″ (51713167)
7.15 PROP’L RMT HANDLE ASM (51713182)
7.16 CABLE ASM 14GA 6WIRE X 35′ (51713199)
7.17 HYD KIT (91715637-1)
7.18 HYD KIT (91715637-2)
7.19 HYD KIT (91715637-3)
7.20 VALVEBANK (73733395)
7.21 CABLE ASM (70733394-1)
7.22 CABLE ASM (70733394-2)
7.23 INSTALLATION KIT (93715267)
7.24 DECAL KIT (95717150)
7.25 BOOM SUPPORT ASM-3816/DOM1 (51714181)
7.26 OPTION-RESERVOIR 18 GAL-BULKHEAD (51707798)
7.27 OUTRIGGER KIT-RH FRONT PULLOUT (51714110)
7.28 OPTION-OUTRIGGER KIT-MO/MD-6X4 (51704772)
7.29 OPTION-AUX OUTRIGGERS-MO/MD-6X4 (31703350)
7.30 OPTION-OUTRIGGER KIT-MO/CRANK DN-6X4 (51704773)
7.31 OPTION-AUX OUTRIGGERS-MO/CRANK DN-6X4 (31703354)
7.32 OPTION-OUTRIGGER KIT-MO/PD-6X4 (31705760)
7.33 OPTION-AUX OUTRIGGERS-MO/PD-6X4 (31710966) (EFF 9-03 – USES VALVEBANK 51714813)
7.34 OPTION-AUX OUTRIGGERS-MO/PD-6X4 (31710966) (THRU 9-03 – USES VALVEBANK 51705983)
7.35 OPTION-OUTRIGGER KIT-PO/PD-6X4 (31706425)
7.36 OPTION-AUX OUTRIGGERS-PO/PD-6X4 (31710967)
7.37 CYLINDER (3B205010)
7.38 CYLINDER-PWR OUT (3B142860)
7.39 VALVEBANK ASM-2 SECTION (51705983)
7.40 VALVEBANK ASM-2 SECTION (51714813)
7.41 VALVEBANK ASM-3 SECTION OR – PO/PD (51714812)
7.42 VALVEBANK ASM-3 SECTION (51705984)
7.43 VALVEBANK ASM (51714381)
7.44 COUNTERBALANCE VALVE ASM (73540057)
7.45 CHASSIS WIRING HARNESS (99903340)
8 GENERAL REFERENCE
8.1 INSPECTION CHECKLIST
8.2 WIRE ROPE INSPECTION
8.3 HOOK INSPECTION
8.4 HOLDING VALVE INSPECTION
8.5 ANTI-TWO-BLOCK DEVICE INSPECTION
8.6 TORQUE CHART – DOMESTIC
8.7 TORQUE CHART – METRIC
8.8 TURNTABLE BEARING FASTENER TIGHTENING SEQUENCE
8.9 TURNTABLE BEARING INSPECTION FOR REPLACEMENT
9 TELESCOPIC CRANE OPERATION & SAFETY MANUAL
10 WARRANTY POLICY