komatsu d275ax 5e0 bull dozer operation and maintenance manual ten00479 01 1

komatsu d275ax 5e0 bull dozer operation and maintenance manual ten00479 01 2

komatsu d275ax 5e0 bull dozer operation and maintenance manual ten00479 01 3

komatsu d275ax 5e0 bull dozer operation and maintenance manual ten00479 01 4

komatsu d275ax 5e0 bull dozer operation and maintenance manual ten00479 01 5

Komatsu D275AX-5E0 Bull Dozer Operation and Maintenance Manual TEN00479-01

$20.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: TEN00479-01
Format: PDF
Size: 9.1MB
Number of Pages: 337

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- D275AX-5E0 Bull Dozer

1. COVER
2. FOREWORD
2.1. BEFORE READING THIS MANUAL
2.2. SAFETY INFORMATION
2.3. INTRODUCTION
2.3.1. USE OF MACHINE
2.3.2. FRONT/REAR, LEFT/RIGHT DIRECTIONS OF MACHINE
2.3.3. VISIBILITY FROM OPERATORS SEAT
2.4. NECESSARY INFORMATION
2.4.1. PRODUCT IDENTIFICATION NUMBER (PIN), MACHINE SERIAL NO. PLATE
2.4.2. EPA REGULATIONS, ENGINE NUMBER PLATE
2.4.3. BLADE SERIAL NO. PLATE POSITION
2.4.4. RIPPER SERIAL NO. PLATE POSITION
2.4.5. POSITION OF SERVICE METER
2.4.6. TABLE TO ENTER SERIAL NO. AND DISTRIBUTOR
2.5. CONTENTS
3. SAFETY
3.1. SAFETY
3.2. SAFETY LABELS
3.2.1. POSITIONS OF SAFETY PICTOGRAMS
3.2.2. SAFETY LABELS
3.3. GENERAL PRECAUTIONS COMMON TO OPERATION AND MAINTENANCE
3.3.1. PRECAUTIONS BEFORE STARTING OPERATION
3.3.2. PREPARATIONS FOR SAFE OPERATION
3.3.3. FIRE PREVENTION
3.3.4. PRECAUTIONS WHEN GETTING ON OR OFF MACHINE
3.3.5. DO NOT GET CAUGHT IN WORK EQUIPMENT
3.3.6. PRECAUTIONS RELATED TO PROTECTIVE STRUCTURES
3.3.7. UNAUTHORIZED MODIFICATION
3.3.8. PRECAUTIONS RELATED TO ATTACHMENTS AND OPTIONS
3.3.9. PRECAUTIONS WHEN RUNNING ENGINE INSIDE BUILDING
3.4. PRECAUTIONS FOR OPERATION
3.4.1. PRECAUTIONS FOR JOBSITE
3.4.2. STARTING ENGINE
3.4.3. OPERATION
3.4.4. TRANSPORTATION
3.4.5. TOWING
3.5. PRECAUTIONS FOR MAINTENANCE
3.5.1. PRECAUTIONS BEFORE STARTING INSPECTION AND MAINTENANCE
3.5.2. PRECAUTIONS FOR INSPECTION AND MAINTENANCE
4. OPERATION
4.1. GENERAL VIEW
4.1.1. GENERAL VIEW OF MACHINE
4.1.2. GENERAL VIEW OF CONTROLS AND GAUGES
4.2. EXPLANATION OF COMPONENTS
4.2.1. FRONT PANEL
4.2.2. SWITCHES
4.2.3. CONTROL LEVERS, PEDALS
4.2.4. SASH GLASS INTERMEDIATE LOCK
4.2.5. DOOR POCKET
4.2.6. ASHTRAY
4.2.7. TOOL BOX
4.2.8. CAR STEREO, HANDLING
4.2.9. AIR CONDITIONER, HANDLING
4.3. OPERATION
4.3.1. CHECK BEFORE STARTING ENGINE, ADJUST
4.3.2. STARTING ENGINE
4.3.3. OPERATIONS AND CHECKS AFTER STARTING ENGINE
4.3.4. STOPPING ENGINE
4.3.5. MOVING MACHINE
4.3.6. STOPPING MACHINE
4.3.7. SHIFTING GEAR
4.3.8. SHIFTING BETWEEN FORWARD AND REVERSE
4.3.9. STEERING MACHINE
4.3.10. PRECAUTIONS FOR OPERATION
4.3.11. PARKING MACHINE
4.3.12. CHECK AFTER STOPPING ENGINE
4.3.13. CHECK AFTER FINISHING WORK
4.3.14. LOCKING
4.3.15. WORK POSSIBLE USING BULLDOZER
4.3.16. EFFECTIVE USE OF MODE SELECTION SYSTEM
4.3.17. RIPPER OPERATION
4.3.18. OPERATING METHOD FOR RIPPING OPERATIONS
4.3.19. ADJUSTING POSTURE OF WORK EQUIPMENT
4.3.20. TIPS FOR LONGER UNDERCARRIAGE LIFE
4.4. TRANSPORTATION
4.4.1. TRANSPORTATION PROCEDURE
4.4.2. LOADING, UNLOADING WORK
4.4.3. METHOD OF LIFTING MACHINE
4.4.4. TRAVELING ON ROADS
4.4.5. REMOVAL OF CAB
4.4.6. INSTALLATION OF CAB
4.5. COLD WEATHER OPERATION
4.5.1. PRECAUTIONS FOR LOW TEMPERATURE
4.5.2. AFTER COMPLETION OF WORK
4.5.3. AFTER COLD WEATHER
4.6. LONGTERM STORAGE
4.6.1. BEFORE STORAGE
4.6.2. DURING STORAGE
4.6.3. AFTER STORAGE
4.6.4. STARTING MACHINE AFTER LONGTERM STORAGE
4.7. TROUBLESHOOTING
4.7.1. AFTER RUNNING OUT OF FUEL
4.7.2. METHOD OF TOWING MACHINE
4.7.3. IF BATTERY IS DISCHARGED
4.7.4. OTHER TROUBLE
4.7.5. WHEN MODE SELECTION SYSTEM FLASHES
5. MAINTENANCE
5.1. GUIDES TO MAINTENANCE
5.2. OUTLINES OF SERVICE
5.2.1. HANDLING OIL, FUEL, COOLANT, AND PERFORMING OIL CLINIC
5.2.2. OUTLINE OF ELECTRIC SYSTEM
5.2.3. HANDLING HYDRAULIC RELATED EQUIPMENT
5.3. WEAR PARTS
5.3.1. WEAR PARTS LIST
5.4. RECOMMENDED FUEL, COOLANT, AND LUBRICANT
5.4.1. RECOMMENDED BRANDS, RECOMMENDED QUALITY FOR PRODUCTS OTHER THAN KOMATSU GENUINE OIL
5.5. STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS
5.5.1. TORQUE LIST
5.6. PERIODIC REPLACEMENT OF SAFETY CRITICAL PARTS
5.6.1. SAFETY CRITICAL PARTS
5.7. MAINTENANCE SCHEDULE CHART
5.7.1. MAINTENANCE SCHEDULE CHART
5.8. SERVICE PROCEDURE
5.8.1. INITIAL 250 HOURS SERVICE (ONLY AFTER THE FIRST 250 HOURS)
5.8.2. WHEN REQUIRED
5.8.3. CHECK BEFORE STARTING
5.8.4. EVERY 250 HOURS SERVICE
5.8.5. EVERY 500 HOURS SERVICE
5.8.6. EVERY 1000 HOURS SERVICE
5.8.7. EVERY 2000 HOURS SERVICE
5.8.8. EVERY 4000 HOURS SERVICE
5.8.9. EVERY 8000 HOURS SERVICE
6. SPECIFICATIONS
6.1. SPECIFICATIONS
7. ATTACHMENTS, OPTIONS
7.1. GENERAL PRECAUTIONS
7.1.1. PRECAUTIONS RELATED TO SAFETY
7.2. SELECTION OF TRACK SHOE
7.2.1. SELECTION OF TRACK SHOES
7.3. PROCEDURE FOR SELECTING RIPPER POINT
7.4. STARTING IN COLD AREAS
7.4.1. EXTERNAL POWER SOURCE TYPE PREHEATING HEATER
7.5. EFFECTIVE METHOD OF OPERATION FOR DUAL TILTDOZER
7.5.1. BLADE CONDITION
7.5.2. DOZING WORK
7.5.3. LEVELING (SPREADING) OPERATION
7.5.4. DITCHING OPERATION
7.5.5. BOULDER RAISING OPERATION
7.5.6. SIDECUTTING OPERATIONS
7.5.7. HORIZONTAL DOZING OPERATIONS FROM SIDE SLOPE (ROUGH GROUND)
7.6. SHOE SLIP CONTROL
7.6.1. MODE SELECTION SWITCH PANEL (SHOE SLIP CONTROL)
7.6.2. EFFECTIVE USE OF MODE SELECTION SYSTEM
7.6.3. IF MODE SELECTION SYSTEM FLASHES
7.7. HANDLING MACHINES EQUIPPED WITH KOMTRAX
7.7.1. BASIC PRECAUTIONS
8. INDEX

Rate this product