komatsu d51exi 24 d51pxi 24 bull dozer operation and maintenance manual ten00938 00 1 1

komatsu d51exi 24 d51pxi 24 bull dozer operation and maintenance manual ten00938 00 2 1

komatsu d51exi 24 d51pxi 24 bull dozer operation and maintenance manual ten00938 00 3 1

komatsu d51exi 24 d51pxi 24 bull dozer operation and maintenance manual ten00938 00 4 1

komatsu d51exi 24 d51pxi 24 bull dozer operation and maintenance manual ten00938 00 5 1

Komatsu D51EXi-24, D51PXi-24 Bull Dozer Operation and Maintenance Manual TEN00938-00

$20.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: TEN00938-00
Format: PDF
Size: 14.8MB
Number of Pages: 244

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- D51EXi-24 Bull Dozer
- D51PXi-24 Bull Dozer

1. COVER
2. FOREWORD
2.1. CONTENTS
2.2. READ THIS MANUAL
2.3. SAFETY INFORMATION
2.4. INTRODUCTION
2.4.1. intelligent Machine Control
2.4.2. MACHINE FEATURES
3. SAFETY
3.1. GENERAL PRECAUTIONS COMMON TO OPERATION AND MAINTENANCE
3.1.1. PRECAUTIONS WHEN GETTING ON OR OFF MACHINE
3.1.1.1. PRECAUTIONS WHEN STANDING UP FROM OPERATORS SEAT
3.1.1.2. PRECAUTIONS WHEN LEAVING MACHINE
3.1.2. PRECAUTIONS FOR BLADE AUTOMATIC CONTROL
3.2. PRECAUTIONS FOR OPERATION
3.2.1. START ENGINE
3.2.1.1. IN COLD WEATHER
3.3. PRECAUTIONS FOR MAINTENANCE
3.3.1. PRECAUTIONS FOR CHECK AND MAINTENANCE
3.3.1.1. PRECAUTIONS FOR GNSS ANTENNA
4. OPERATION
4.1. GENERAL VIEW
4.1.1. MACHINE EQUIPMENT NAME
4.1.2. MACHINE OUTSIDE EQUIPMENT NAME
4.1.3. CONTROLS AND GAUGES NAMES
4.1.3.1. CONTROL BOX NAME
4.2. EXPLANATION OF COMPONENTS
4.2.1. intelligent Machine Control SYSTEM
4.2.1.1. CONTROL BOX
4.2.1.2. NETWORK MODEM
4.2.1.3. AUTO/MANUAL SWITCH
4.2.1.4. CUT/FILL OFFSETS SWITCH
4.2.1.5. BACK GRADE MODE SWITCH
4.2.1.6. GNSS ANTENNA
4.2.1.7. GNSS RECEIVER
4.2.2. OTHER EQUIPMENT
4.2.2.1. LUNCH BOX FIXING BELT
4.2.2.2. METHOD FOR REMOVING AND INSTALLING CONTROL BOX
4.3. MACHINE OPERATIONS AND CONTROLS
4.3.1. CHECKS AND ADJUSTMENT BEFORE STARTING ENGINE
4.3.2. OPERATIONS AND CHECKS AFTER STARTING ENGINE
4.3.2.1. RESET CYLINDER STROKE END
4.3.3. METHOD FOR STOPPING ENGINE
4.3.4. METHOD FOR USING AUTOMATIC BLADE CONTROL
4.3.4.1. PREPARATIONS FOR BLADE AUTOMATIC CONTROL
4.3.4.2. HANDLE AUTOMATIC BLADE CONTROL
4.3.4.3. MODE SETTINGS
4.3.4.4. FUNCTION RELATED WITH MACHINE MONITOR BLADE AUTOMATIC CONTROL
4.3.4.5. PRECAUTIONS WHEN USING BLADE AUTOMATIC CONTROL
4.3.4.6. RECOMMENDED APPLICATIONS AND MODES
4.4. TRANSPORTATION
4.4.1. REMOVE RADIO DEVICE ANTENNA CABLE
4.5. PRECAUTIONS FOR LONGTERM STORAGE
4.5.1. TURN BATTERY DISCONNECT SWITCH TO OFF POSITION BEFORE LONGTERM STORAGE
4.6. TROUBLES AND ACTIONS
4.6.1. OTHER TROUBLE
4.6.1.1. PHENOMENA AND ACTIONS FOR CONTROL BOX
5. HANDLE CONTROL BOX
5.1. TABLE OF CONTENTS
5.2. INTRODUCTION
5.2.1. FUNCTION OF SWITCHES
5.2.1.1. POWER ON/OFF AND MENU SWITCH
5.2.1.2. ZOOM IN SWITCH
5.2.1.3. ZOOM OUT SWITCH
5.2.1.4. TOGGLE MAIN VIEW SWITCH
5.2.2. BRIGHTNESS AND VOLUME CONTROL
5.2.3. LED INDICATOR
5.2.4. KEYBOARD FUNCTIONS
5.2.4.1. METHOD FOR INPUTTING WITH ALPHANUMERIC KEYBOARD
5.2.4.2. METHOD FOR INPUTTING WITH NUMERIC KEYBOARD
5.2.5. METHOD FOR DISPLAYING MAIN MENU
5.3. FILE MENU
5.3.1. PROJECT FILES
5.3.1.1. METHOD FOR IMPORTING AND SETTING PROJECT FILES
5.3.1.2. METHOD FOR CREATING A PROJECT FILE
5.3.1.3. METHOD FOR EXPORTING A PROJECT FILE
5.3.2. CONTROL POINT FILES
5.3.2.1. METHOD FOR IMPORTING CONTROL POINT FILES
5.3.3. LAYERS
5.3.3.1. METHOD FOR IMPORTING LAYERS
5.3.4. POINT DATA
5.3.4.1. METHOD FOR REGISTERING POINT DATA
5.3.5. SURFACE FILE
5.3.5.1. METHOD FOR IMPORTING SURFACE FILES
5.3.5.2. METHOD FOR CREATING FLAT SURFACE FILES
5.3.5.3. METHOD FOR CREATING SLOPING SURFACE FILES
5.3.5.4. METHOD FOR CREATING CROWN ROAD SURFACE FILES
5.3.5.5. METHOD FOR CREATING TRIANGULATED SURFACES FROM A TOPO SURVEY FILE
5.3.5.6. METHOD FOR CREATING SURFACE FILES AFTER REFLECTING RAISE OR LOWER AMOUNT OF AN EXISTING SURFACE
5.3.5.7. METHOD FOR CREATING ALIGNMENT FILE OF SUBGRADE OF ACTIVE ALIGNMENT
5.3.6. ACTIVE FILE
5.3.6.1. METHOD FOR SELECTING AN ACTIVE SURFACE FILE
5.3.6.2. METHOD FOR SELECTING AN ACTIVE ALIGNMENT FILE
5.3.6.3. METHOD FOR SELECTING AN ACTIVE ASBUILT VIEW
5.3.7. EXIT 3DMC
5.3.7.1. METHOD FOR EXITING 3DMC
5.4. CONTROL MENU
5.4.1. MACHINE SETTING
5.4.1.1. SET FOR CONNECTING TO MACHINE
5.4.2. METHOD FOR SETTING ASBUILT CONTROL OPTIONS
5.4.2.1. METHOD FOR ADDING AND SETTING ASBUILT SURFACE DISPLAY
5.4.2.2. METHOD FOR DELETING ASBUILT SURFACE DISPLAY
5.4.3. BLADE CONTROL
5.4.3.1. METHOD FOR SETTING AUTOMATIC BESTFIT BLADE CONTROL
5.4.3.2. METHOD FOR SETTING SINGLE POINT BLADE CONTROL
5.4.4. STEER INDICATION OPTIONS
5.4.4.1. METHOD FOR SETTING STEER INDICATION OPTIONS
5.4.5. ADJUST WEAR AMOUNT
5.4.6. DOZING CONTROL
5.4.7. ADJUST BLADE ELEVATION
5.4.8. CALIBRATE BLADE POSITION
5.5. TOOLS MENU
5.5.1. RADIO DEVICE SETTINGS
5.5.2. POSITION SETTINGS
5.5.2.1. METHOD FOR CHECKING BLADE ELEVATION
5.5.3. NAVIGATE POINTS
5.5.3.1. METHOD FOR NAVIGATING TO POINTS
5.5.4. TOPO SHOT FOR TOPOGRAPHIC SURVEY
5.5.4.1. PERFORM TOPOGRAPHIC SURVEYS
5.5.5. METHOD FOR SETTING Sitelink3D
5.5.5.1. SETTING CONTENTS BY Sitelink3D MENU
5.5.6. SUPERVISOR MODE
5.5.6.1. METHOD FOR USING SUPERVISOR MODE
5.5.6.2. METHOD FOR LOCKING MENUS, BUTTONS AND SCREEN ITEMS
5.5.6.3. METHOD FOR CHANGING THE PASSWORD
5.5.6.4. METHOD FOR FINISHING LOCK MODE
5.6. VIEW MENU
5.6.1. MAIN WINDOW DISPLAY
5.6.1.1. METHOD FOR DISPLAYING MAIN WINDOW DISPLAY
5.6.2. LEFT WINDOW DISPLAY
5.6.2.1. METHOD FOR DISPLAYING LEFT WINDOW DISPLAY
5.6.3. RIGHT WINDOW DISPLAY
5.6.3.1. METHOD FOR DISPLAYING RIGHT WINDOW DISPLAY
5.6.4. LOWER WINDOW DISPLAY
5.6.4.1. METHOD FOR DISPLAYING LOWER WINDOW DISPLAY
5.6.5. DISPLAY OPTIONS
5.6.5.1. METHOD FOR DISPLAYING DISPLAY OPTIONS
5.6.5.2. METHOD FOR SETTING WORKING SURFACE DISPLAY
5.6.5.3. METHOD FOR SETTING ALIGNMENT DISPLAY
5.6.5.4. METHOD FOR SETTING ASBUILT SURFACE DISPLAY
5.6.5.5. METHOD FOR SETTING POINT DISPLAY
5.6.5.6. METHOD FOR SETTING SHORTCUTS DISPLAY
5.6.5.7. METHOD FOR SETTING BACKGROUND COLOR DISPLAY
5.6.5.8. METHOD FOR SETTING DISPLAYED UNITS
5.6.5.9. METHOD FOR SELECTING LANGUAGE
5.6.6.1. METHOD FOR DISPLAYING 3DMC INFORMATION
5.7. MAIN WINDOW DISPLAY
5.7.1. ELEVATION CONTROL KEY
5.7.2. SLOPE CONTROL KEY
5.7.3. SHORTCUT ON THE MAIN WINDOW
5.7.3.1. TOGGLE ASBUILT MODE
5.7.3.2. START/STOP ASBUILT UPDATES
5.7.3.3. DOZING MODE SELECTION
5.7.3.4. BLADE LOAD SELECTION
5.7.3.5. TAKE A TOPO SHOT
5.7.3.6. TASK DETAIL
5.7.3.7. Sitelink3D MESSAGING
5.7.3.8. Sitelink3D ACTIVITY
5.7.3.9. MATERIAL SELECTION
5.7.4. PAN OF MAIN MAP VIEW
5.8. OPERATION ON MAIN MENU
5.8.1. METHOD FOR DISPLAYING GNSS INFORMATION
5.8.2. METHOD FOR ADJUSTING CUT/FILL OFFSETS
5.8.3. METHOD FOR CHANGING GRADE INDICATOR DISPLAY
5.8.3.1. METHOD FOR CHANGING SLOPE DISPLAY
5.8.3.2. METHOD FOR CHANGING ON GRADE
5.8.3.3. METHOD FOR CHANGING RANGE
5.8.3.4. METHOD FOR CHANGING HIGHLIGHT COLOR
5.8.4. METHOD FOR CHANGING DISPLAY OF LIGHT BAR
5.8.5. OPERATION USING POPUP MENU
5.8.5.1. DISPLAY EXTENDED STATUS TEXT IN PLAN/PROFILE/SECTION
5.8.5.2. METHOD FOR ADJUSTING CUT/FILL OFFSETS (POPUP MENU)
5.8.5.3. METHOD FOR NAVIGATING TO POINTS (POPUP MENU)
5.8.5.4. METHOD FOR USING POLYLINE
5.8.5.5. MOVE THE STEER POINT (POP UP MENU)
5.8.5.6. METHOD FOR SETTING ISOLATE SURFACE REGION
6. SPECIFICATIONS
6.1. SPECIFICATIONS
6.1.1. SPECIFICATIONS D51EXI24
6.1.2. SPECIFICATIONS D51PXI24
7. INDEX

Rate this product