komatsu d85ms 15 demining equipment operation and maintenance manual pen00241 02 1

komatsu d85ms 15 demining equipment operation and maintenance manual pen00241 02 2

komatsu d85ms 15 demining equipment operation and maintenance manual pen00241 02 3

komatsu d85ms 15 demining equipment operation and maintenance manual pen00241 02 4

komatsu d85ms 15 demining equipment operation and maintenance manual pen00241 02 5

Komatsu D85MS-15 Demining Equipment Operation and Maintenance Manual PEN00241-02

$20.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: PEN00241-02
Format: PDF
Size: 9.0MB
Number of Pages: 291

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- D85MS-15 Demining Equipment

1. COVER
2. FOREWORD
2.1. FOREWORD
2.2. SAFETY INFORMATION
2.3. INTRODUCTION
2.3.1. FRONT/REAR, LEFT/RIGHT DIRECTIONS OF MACHINE
2.3.2. BREAKING IN THE MACHINE
2.4. NECESSARY INFORMATION
2.4.1. PRODUCT IDENTIFICATION NUMBER (PIN), MACHINE SERIAL NO. PLATE
2.4.2. ENGINE SERIAL NO. PLATE
2.4.3. LOCATION OF DEMINING ROTOR AND SERIAL NUMBER PLATE
2.4.4. BLADE SERIAL NO. PLATE POSITION
2.4.5. RIPPER SERIAL NO. PLATE POSITION
2.4.6. POSITION OF SERVICE METER
2.4.7. TABLE TO ENTER SERIAL NO. AND DISTRIBUTOR
2.5. CONTENTS
3. SAFETY
3.1. SAFETY
3.2. SAFETY LABELS
3.2.1. POSITIONS OF SAFETY PICTOGRAMS
3.2.2. SAFETY LABELS
3.3. GENERAL PRECAUTIONS
3.4. PRECAUTIONS FOR OPERATION
3.4.1. BEFORE STARTING ENGINE
3.4.2. OPERATION
3.4.3. TRANSPORTATION
3.4.4. BATTERY
3.4.5. TOWING
3.5. PRECAUTIONS FOR MAINTENANCE
4. OPERATION
4.1. GENERAL VIEW
4.1.1. GENERAL VIEW OF MACHINE
4.1.2. GENERAL VIEW OF CONTROLS AND GAUGES
4.2. EXPLANATION OF COMPONENTS
4.2.1. FRONT PANEL
4.2.2. SWITCHES
4.2.3. CONTROL LEVERS, PEDALS
4.2.4. CAR STEREO, HANDLING
4.2.5. AIR CONDITIONER
4.2.6. CAR RADIO, HANDLING
4.2.7. ACCUMULATOR, HANDLING
4.3. OPERATION
4.3.1. CHECK BEFORE STARTING ENGINE, ADJUST
4.3.2. STARTING ENGINE
4.3.3. OPERATIONS AND CHECKS AFTER STARTING ENGINE
4.3.4. STOPPING ENGINE
4.3.5. MOVING MACHINE
4.3.6. STOPPING MACHINE
4.3.7. SHIFTING GEAR
4.3.8. SHIFTING BETWEEN FORWARD AND REVERSE
4.3.9. STEERING MACHINE
4.3.10. PRECAUTIONS FOR OPERATION
4.3.11. PARKING MACHINE
4.3.12. CHECK AFTER STOPPING ENGINE
4.3.13. CHECK AFTER FINISHING WORK
4.3.14. LOCKING
4.3.15. WORK THAT CAN BE DONE USING DEMINING ROTOR
4.3.16. PRECAUTIONS FOR DEMINING OPERATIONS
4.3.17. WORK POSSIBLE USING BULLDOZER
4.3.18. ADJUSTING POSTURE OF WORK EQUIPMENT
4.3.19. TIPS FOR LONGER UNDERCARRIAGE LIFE
4.4. TRANSPORTATION
4.4.1. TRANSPORTATION PROCEDURE
4.4.2. LOADING, UNLOADING WORK
4.4.3. PRECAUTIONS FOR LOADING
4.4.4. METHOD OF LIFTING MACHINE
4.4.5. PRECAUTIONS FOR TRANSPORTATION
4.4.6. TRAVELING ON ROADS
4.4.7. REMOVAL OF CAB
4.4.8. INSTALLATION OF CAB
4.5. COLD WEATHER OPERATION
4.5.1. PRECAUTIONS FOR LOW TEMPERATURE
4.5.2. AFTER COMPLETION OF WORK
4.5.3. AFTER COLD WEATHER
4.6. LONGTERM STORAGE
4.6.1. BEFORE STORAGE
4.6.2. DURING STORAGE
4.6.3. AFTER STORAGE
4.7. TROUBLESHOOTING
4.7.1. AFTER RUNNING OUT OF FUEL
4.7.2. METHOD OF TOWING MACHINE
4.7.3. IF BATTERY IS DISCHARGED
4.7.4. OTHER TROUBLE
5. MAINTENANCE
5.1. GUIDES TO MAINTENANCE
5.2. OUTLINES OF SERVICE
5.2.1. HANDLING OIL, FUEL, COOLANT, AND PERFORMING OIL CLINIC
5.2.2. OUTLINE OF ELECTRIC SYSTEM
5.2.3. HANDLING HYDRAULIC RELATED EQUIPMENT
5.3. WEAR PARTS
5.3.1. WEAR PARTS LIST
5.4. RECOMMENDED FUEL, COOLANT, AND LUBRICANT
5.4.1. USE OF FUEL, COOLANT AND LUBRICANTS ACCORDING TO AMBIENT TEMPERATURE
5.4.2. RECOMMENDED BRANDS, RECOMMENDED QUALITY FOR PRODUCTS OTHER THAN KOMATSU GENUINE OIL
5.5. STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS
5.5.1. TORQUE LIST
5.6. PERIODIC REPLACEMENT OF SAFETY CRITICAL PARTS
5.6.1. SAFETY CRITICAL PARTS
5.7. MAINTENANCE SCHEDULE CHART
5.7.1. MAINTENANCE SCHEDULE CHART
5.8. SERVICE PROCEDURE
5.8.1. INITIAL 250 HOURS SERVICE (ONLY AFTER THE FIRST 250 HOURS)
5.8.2. WHEN REQUIRED
5.8.3. CHECK BEFORE STARTING
5.8.4. EVERY 250 HOURS SERVICE
5.8.5. EVERY 500 HOURS SERVICE
5.8.6. EVERY 1000 HOURS SERVICE
5.8.7. EVERY 2000 HOURS SERVICE
5.8.8. EVERY 4000 HOURS SERVICE
5.8.9. EVERY 8000 HOURS SERVICE
6. SPECIFICATIONS
6.1. SPECIFICATIONS
7. ATTACHMENTS, OPTIONS
7.1. GENERAL PRECAUTIONS
7.1.1. PRECAUTIONS RELATED TO SAFETY
7.2. SELECTION OF TRACK SHOE
7.2.1. SELECTION OF TRACK SHOES
7.3. PROCEDURE FOR SELECTING RIPPER POINT
7.3.1. PROCEDURE FOR SELECTING RIPPER POINT
7.4. CAP WITH LOCK, HANDLING
7.4.1. METHOD OF OPENING AND CLOSING CAP WITH LOCK
8. INDEX

Rate this product