komatsu gd675 7e0 motor grader operation and maintenance manual pen01997 01 1

komatsu gd675 7e0 motor grader operation and maintenance manual pen01997 01 2

komatsu gd675 7e0 motor grader operation and maintenance manual pen01997 01 3

komatsu gd675 7e0 motor grader operation and maintenance manual pen01997 01 4

komatsu gd675 7e0 motor grader operation and maintenance manual pen01997 01 5

Komatsu GD675-7E0 Motor Grader Operation and Maintenance Manual PEN01997-01

$20.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: PEN01997-01
Format: PDF
Size: 26.8MB
Number of Pages: 605

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- GD675-7E0 Motor Grader

1. Cover
2. Foreword
2.1. Table of Contents
2.2. Foreword
2.3. Safety Information
2.4. Safety Labels
2.5. Noise Emission Levels
2.6. Vibration Level
2.7. Introduction
2.8. Engine Technology to Conform Exhaust Gas Emission
2.9. Machine Information
2.9.1. Location of Product Identification Number (PIN) and Machine Serial No. Plate
2.9.2. Location of Engine Number Plate
2.9.3. Fluorinated Greenhouse Gases
2.9.4. Service Meter Location
2.9.5. Your Machine Serial Numbers and Distributor
2.9.6. Serial Plate
2.9.7. Declaration of Conformity
2.10. Abbreviation List
3. Safety
3.1. Safety Labels
3.2. General Precautions Common to Operation and Maintenance
3.2.1. Precautions Before You Start Operation
3.2.2. Prepare for Safety Operation
3.2.3. Procedures If Fire Occurs
3.2.4. Precautions to Prevent Fire
3.2.5. Precautions When You Get on or Off Machine
3.2.6. Precautions for Machine and Jobsite
3.3. Precautions for Operation
3.3.1. Precautions for Jobsite
3.3.2. Start Engine
3.3.3. Precautions for Operation
3.3.4. Precautions for Transportation
3.3.5. Towing and being Towed
3.4. Precautions for Maintenance
3.4.1. Precautions Before Inspection and Maintenance
3.4.2. Precautions for Check and Maintenance
3.5. Precautions for Tire
3.6. Precautions for DEF
4. Operation
4.1. General View
4.1.1. Names of Machine Equipment
4.1.2. Control Levers and Pedals
4.1.3. Names of Other Equipment
4.2. Explanation of Components
4.2.1. Machine Monitor Equipment
4.2.2. Names of Switch Panel Equipment
4.2.3. Control Levers and Pedals
4.2.4. Other Equipment
4.3. Machine Operations and Controls
4.3.1. Checks and Adjustment Before You Start Engine
4.3.2. How to Start Engine
4.3.3. Operations and Checks After You Start Engine
4.3.4. How to Stop Engine
4.3.5. How to Examine After You Stop Engine
4.3.6. Start Machine (Travel FORWARD and REVERSE, Gear Shift) and Stop Machine
4.3.7. How to Steer Machine
4.3.8. How to Operate Work Equipment
4.3.9. Work Precautions
4.3.10. Adjust Work Equipment Posture
4.3.11. Handle Blade Accumulator
4.3.12. Recommended Applications
4.3.13. Park Machine
4.3.14. How to Examine After You Complete Work
4.3.15. Lock
4.3.16. Handle Tires
4.4. Handle Air Conditioner
4.4.1. Air Conditioner Equipment
4.4.2. Operate Air Conditioner
4.5. Handle Radio
4.5.1. Explanation of Radio Equipment
4.5.2. Operate Radio
4.5.3. Radio Setting
4.6. Transportation
4.6.1. Select Transportation Method
4.6.2. Precautions When You Transport Machine
4.6.3. Load onto and Unload from a Trailer
4.6.4. How to Secure Machine
4.6.5. How to Lift Machine
4.7. Cold Weather Operation
4.7.1. Cold Weather Operation Information
4.7.2. Precautions After Daily Work Ends in Cold Weather
4.7.3. In Cold Weather
4.7.4. After Cold Weather Season
4.8. LongTerm Storage Precautions
4.8.1. Prepare for LongTerm Storage
4.8.2. Maintenance During LongTerm Storage
4.8.3. How to Start Machine After LongTerm Storage
4.9. Troubles and Procedures
4.9.1. Procedures When You Run Out of Fuel
4.9.2. If Leaning Piping is Broken
4.9.3. Use Leaning Stopper
4.9.4. Precautions When You Tow Machine
4.9.5. Precautions for Discharged Battery
4.9.6. Lower Work Equipment (Release Work Equipment Hydraulic Pressure) While Engine is Off
4.9.7. Other Trouble
5. Maintenance
5.1. Precautions for Maintenance
5.2. Maintenance Information
5.2.1. Oil, Fuel, and Coolant
5.2.2. Battery Terminal
5.2.3. Electrical Components
5.3. Standard Tightening Torque for Bolts and Nuts
5.4. Maintenance Schedule
5.4.1. Maintenance Schedule Table
5.5. Maintenance Procedure
5.5.1. Initial 250 Hours Maintenance (Only After the First 250 Hours)
5.5.2. Initial 1000 Hours Maintenance (Only After the First 1000 Hours)
5.5.3. When Required
5.5.4. Examine Before You Start Operation
5.5.5. Every 50 Hours Maintenance
5.5.6. Every 250 Hours Maintenance
5.5.7. Every 500 Hours Maintenance
5.5.8. Every 1000 Hours Maintenance
5.5.9. Every 2000 Hours Maintenance
5.5.10. Every 4000 Hours Maintenance
5.5.11. Every 4500 Hours Maintenance
5.5.12. Every 8000 Hours Maintenance
5.5.13. Every 9000 Hours Maintenance
6. Specifications
6.1. Specifications
7. Attachments and Options
7.1. Machines with ICT Devices
7.1.1. Precautions for Machines with ICT Devices
7.2. Machine with Cross Slope System
7.2.1. Overview of Machine with Cross Slope System
7.2.2. Precautions for Machine with Cross Slope System
7.2.3. Components on Machines with Cross Slope System
7.2.4. Use Cross Slope System
8. Replacement Parts
8.1. Defined Life Parts
8.1.1. Defined Life Parts List
8.2. Consumable Parts
8.2.1. Consumable Parts List
8.3. Recommended Fuel, Coolant, and Lubricant
8.3.1. Lubrication Chart
8.3.2. How to Use Fuel, Coolant and Lubricants by Ambient Temperature
8.3.3. Recommended Brands and Qualities Other Than Komatsu Genuine Oils
9. Index

Rate this product