Komatsu Payload Meter II Operation and Maintenance Manual CEAM006301

Komatsu Payload Meter II Operation and Maintenance Manual CEAM006301 - Image 2

Komatsu Payload Meter II Operation and Maintenance Manual CEAM006301 - Image 3

Komatsu Payload Meter II Operation and Maintenance Manual CEAM006301 - Image 4

Komatsu Payload Meter II Operation and Maintenance Manual CEAM006301 - Image 5

komatsu payload meter ii operation and maintenance manual ceam006301 2

komatsu payload meter ii operation and maintenance manual ceam006301 3

Komatsu Payload Meter II Operation and Maintenance Manual CEAM006301

$20.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: CEAM006301
Format: PDF
Size: 0.9MB
Number of Pages: 69

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- Payload Meter II

1. MAIN MENU
2. COVER
3. CONTENTS
4. GENERAL INFORMATION
5. LIGHTS, SWITCHES, AND COMPONENTS
6. TIPS FOR OPERATION
7. EXTERNAL DISPLAY LIGHTS
8. THEORY OF OPERATION
8.1. BASIC DESCRIPTION
8.2. INCLINOMETER
8.3. LINKAGE FACTOR
8.4. GAIN FACTOR
8.5. BRAKE LOCK
8.6. SOURCES OF ERROR
8.7. TYPICAL DATA FROM SERVICE CHECK MODE
8.8. EXAMPLE CALCULATION OF PAYLOAD
8.9. VIEWING PAYLOAD CALCULATION INPUTS
8.10. CHECKING THE GAIN
8.11. ADJUSTING THE GAIN
9. TYPES OF DATA STORED
9.1. CYCLE DATA
9.2. ENGINE ON/OFF DATA
9.3. FAULT CODES AND WARNING DATA
9.4. ENGINE OPERATION
9.5. TOTAL PAYLOAD AND TOTAL NUMBER OF CYCLES
9.6. OTHER DATA
10. OPERATOR FUNCTIONS
10.1. USING THE OPERATOR LOAD COUNTER
10.1.1. DESCRIPTION
10.1.2. VIEWING THE OPERATOR LOAD COUNTER
10.1.3. CLEARING THE OPERATOR LOAD COUNTER
10.1.4. DIMMING THE LIGHTS ON THE DISPLAY
11. INITIAL SETUP OF PAYLOAD METER
11.1. SWITCH SETTINGS
11.2. CHECKING THE OPERATOR CHECK MODE
11.3. CHECKING THE SERVICE CHECK MODE
11.3.1. SETTING UPXX
11.3.2. SETTING PL00
11.4. CHECKING THE Gt SETTING
11.5. CHECKING THE INCLINOMETER SETTINGS
11.6. CALIBRATING A TRUCK
12. DISPLAYS AT STARTUP
13. SETUP AND MAINTENANCE
13.1. SETTING THE SPEED LIMIT
13.2. SETTING THE OPTION CODE
13.3. SETTING THE MACHINE I. D.
13.4. SETTING THE OPERATOR I. D.
13.5. SETTING THE TIME AND DATE
14. DOWNLOAD OF INFORMATION
15. DISPLAY OF FAULT CODES
16. CHARTS OF FAULT CODES AND OTHER INFORMATION
17. MONITORING INPUT SIGNALS
18. SERVICE CHECK MODE
19. UP FACTOR PAYLOAD CALCULATION GAIN
20. PL MODE LOAD CALCULATION TIMING
21. FINAL GEAR RATIO SELECTION
22. BATTERY REPLACEMENT PROCEDURE
22.1. REPLACING THE BATTERY
22.2. AFTER REPLACING THE BATTERY
23. SUSPENSION PRESSURE SENSOR
24. PAYLOAD METER BACK PANEL
25. CONNECTIONS (AMP PIN IDENTIFICATION)
26. PAYLOAD CIRCUIT NUMBERS
27. PAYLOAD METER II REINITIALZATION PROCEDURE
28. TROUBLESHOOTING SECTION
29. COMMON PROBLEMS
29.1. SUSPENSION CHARGING
29.2. SYMPTOM TABLE
29.3. MISSING BODYUP SIGNAL
29.4. MISSING SPEED SIGNAL
29.5. F18 RTERMINAL, OIL PRESSURE SIGNALS
29.6. SHORTED 18V SENSOR POWER SUPPLY (930E)
30. FAULT TREE DIAGNOSIS
30.1. PAYLOAD LIGHTS WONT ILLUMINATE
30.2. RED, AMBER OR GREEN PAYLOAD LIGHT DOES NOT ILLUMINATE
30.3. CANNOT DOWNLOAD PC COMMUNICATIONS
30.4. PC COMMUNICATIONS CONFIGURATION
30.5. CAL PAYLOAD METER WONT CALIBRATE
30.6. F20 SENSOR POWER FAULT
30.7. F21 THRU F28 PRESSURE SENSOR FAULTS
30.8. F31, F32 INCLINOMETER
30.9. BODY UP INPUT
30.10. BRAKE LOCK INPUT
30.11. SPEED SIGNAL
31. CONNECTORS AND PRESSURE SENSORS
32. REALTIME PAYLOAD METER II MONITOR PROGRAM
32.1. DATA DEFINITIONS AND COMMENTS
32.2. TRUCK STATUS AND INPUTS
32.3. MENU FUNCTIONS
32.4. USING SCOPE
32.5. LOG FILE INFORMATION
32.6. CONNECTIONS TO PAYLOAD METER II
33. USING SCOPE
33.1. MONITORING INPUTS USING SCOPE
33.2. MONITORING SUSPENSION CHARGING USING SCOPE
33.3. PRESSURE SENSOR DUMMY LOADS
34. GAIN ADJUSTMENT WORKSHEET

Rate this product