komatsu pc128uu 1 avance hydraulic excavator operation and maintenance manual ceam004200 1

komatsu pc128uu 1 avance hydraulic excavator operation and maintenance manual ceam004200 2

komatsu pc128uu 1 avance hydraulic excavator operation and maintenance manual ceam004200 3

komatsu pc128uu 1 avance hydraulic excavator operation and maintenance manual ceam004200 4

komatsu pc128uu 1 avance hydraulic excavator operation and maintenance manual ceam004200 5

Komatsu PC128UU-1 Avance Hydraulic Excavator Operation and Maintenance Manual CEAM004200

$20.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: CEAM004200
Format: PDF
Size: 8.0MB
Number of Pages: 264

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- PC128UU-1 Avance Hydraulic Excavator

1. MAIN MENU
2. COVER
3. INTRODUCTION
4. SAFETY INFORMATION
5. OVERVIEW OF THE EQUIPMENT
5.1. DESIGNATED USES
5.2. FEATURES OF THIS MACHINE
5.3. BREAKIN
6. MEMO
7. LOCATION OF SERIAL NUMBER PLATES, AND FORM TO ENTER SERIAL NUMBER AND NAME OF THE DISTRIBUTOR
7.1. LOCATION OF SERIAL NUMBER
7.2. LOCATION OF ENGINE SERIAL NUMBER
7.3. FORM FOR ENTERING THE CYLINDER NUMBER AND THE KOMATSU DISTRIBUTOR
8. TABLE OF CONTENTS
9. SAFETY
10. BASIC PRECAUTIONS
11. PRECAUTIONS FOR OPERATING
11.1. BEFORE STARTING THE ENGINE
11.2. AFTER STARTING THE ENGINE
11.3. TRANSPORT THE VEHICLE
11.4. BATTERY
11.5. TOWING
11.6. BUCKET WITH HOOK
12. PRECAUTIONS FOR MAINTENANCE
12.1. PRIOR TO PERFORMING MAINTENANCE
12.2. DURING MAINTENANCE
13. WHERE SAFETY LABELS HAVE BEEN ATTACHED
13.1. WHERE SAFETY LABELS ARE LOCATED
14. OPERATION
15. THE NAME OF EACH PART
15.1. GENERAL DIAGRAM OF THE VEHICLE
15.2. GENERAL VIEW OF CONTROLS AND GAUGES
16. EXPLANATION OF EACH DEVICE
16.1. VEHICLE MONITOR PANEL
16.2. SWITCHES
16.3. CONTROL LEVERS / PEDALS
16.4. ENGINE HOOD
16.5. FRONT WINDOW
16.6. SLIDING DOOR
16.7. FUSE BOX
16.8. FUSIBLE LINK
16.9. LOCKING CAP AND COVERS
16.10. TOOL BOX
16.11. GREASE GUN HOLDER
16.12. CONTROLLERS
16.13. ASHTRAY (OPTIONAL)
16.14. REAR UNDER VIEW MIRROR (OPTIONAL)
16.15. USING THE CAR RADIO
16.16. USING THE AIR CONDITIONER
17. OPERATION
17.1. CHECKS BEFORE STARTING THE ENGINE
17.2. STARTING THE ENGINE
17.3. CHECKS AND TASKS TO BE PERFORMED AFTER STARTING THE ENGINE
17.4. MOVING THE MACHINE
17.5. STEERING THE MACHINE
17.6. STOPPING THE MACHINE
17.7. SWINGING
17.8. PROHIBITED ACTIONS WHILE OPERATING THE MACHINE
17.9. PRECAUTIONS DURING OPERATION
17.10. PRECAUTIONS WHEN CLIMBING OR DESCENDING SLOPES
17.11. EXTRICATING THE MACHINE FROM MUD
17.12. OPERATIONS THAT CAN BE PERFORMED WITH THE HYDRAULIC EXCAVATOR
17.13. CHANGING THE BUCKET
17.14. PARKING THE MACHINE
17.15. CHECKS AFTER COMPLETING OPERATION
17.16. STOPPING THE ENGINE
17.17. CHECKS AFTER THE ENGINE HAS BEEN STOPPED
17.18. LOCKING
17.19. USING THE 4 SYSTEMS
17.20. USING RUBBER TRACK SHOES (FOR MACHINES SPECIFIED FOR USE WITH RUBBER TRACKS)
18. TRANSPORTING
18.1. HOW TO LOAD AND UNLOAD THE VEHICLE
18.2. PRECAUTIONS WHEN CARRYING THINGS
18.3. PRECAUTIONS WHEN TRANSPORTING
19. HANDLING IN COLD WEATHER
19.1. PREPARATION FOR LOW TEMPERATURES
19.2. PRECAUTIONS AFTER COMPLETING OPERATIONS
19.3. PREPARING THE CAR HEATER
19.4. AFTER THE COLD WEATHER SEASON IS OVER
20. LONGTERM STORAGE
20.1. BEFORE STORING THE MACHINE
20.2. DURING STORAGE
20.3. AFTER STORAGE
21. TROUBLESHOOTING
21.1. PHENOMENA THAT ARE NOT BREAKDOWNS
21.2. HOW TO TOW WITH THE MACHINE OR BE TOWED
21.3. HOW TO USE THE HOOK FOR TOWING LIGHT OBJECTS
21.4. PRECAUTIONS FOR SPECIAL JOB SITES
21.5. WHEN THE BATTERY IS DEAD
21.6. WHEN THIS PHENOMENON OCCURS
22. CHECKS AND MAINTENANCE
23. PRECAUTIONS IN PERFORMING CHECKS AND MAINTENANCE
24. BASIC MAINTENANCE
24.1. ESSENTIAL INFORMATION ON OIL, FUEL AND COOLANT
24.2. SUMMARY OF ELECTRICAL SYSTEM
24.3. SUMMARY OF HYDRAULIC SYSTEM
25. CONSUMABLE SUPPLIES
26. USAGE OF FUEL AND LUBRICATING GREASE ACCORDING TO AMBIENT TEMPERATURE
26.1. FUEL / OIL
26.2. COOLANT
27. STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS
27.1. LIST OF TOOLS NECESSARY
27.2. TORQUE TABLE
28. ABOUT REGULAR REPLACEMENT OF IMPORTANT COMPONENTS
29. LIST OF MAINTENANCE
29.1. MAINTENANCE SCHEDULE
29.2. SERVICE TIME WHEN USING HYDRAULIC BREAKERS
29.3. MAINTENANCE SCHEDULE
30. SERVICE PROCEDURES
30.1. INITIAL SERVICE AFTER 250 HOURS OF OPERATION
30.2. MAINTENANCE THAT IS NOT REGULARLY SCHEDULED
30.3. CHECKS BEFORE STARTING OPERATIONS
30.4. SERVICE TO BE PERFORMED AFTER EVERY 50 HOURS OF OPERATION
30.5. SERVICE TO BE PERFORMED AFTER EVERY 100 HOURS OF OPERATION
30.6. SERVICE TO BE PERFORMED AFTER EVERY 250 HOURS OF OPERATION
30.7. SERVICE TO BE PERFORMED AFTER EVERY 500 HOURS OF OPERATION
30.8. SERVICE TO BE PERFORMED AFTER EVERY 1000 HOURS OF OPERATION
30.9. SERVICE TO BE PERFORMED AFTER EVERY 2000 HOURS OF OPERATION
30.10. SERVICE TO BE PERFORMED AFTER EVERY 4000 HOURS OF OPERATION
31. INSPECTIONS REQUIRED
31.1. BEFORE BEGINNING WORK (CHECKS PRIOR TO STARTING OPERATIONS)
31.2. CHECKS BEFORE BEGINNING WORK (CHECKS PRIOR TO STARTING OPERATIONS)
32. SPECIFICATIONS
33. SPECIFICATIONS
34. OPTIONAL PARTS, ATTACHMENTS
35. GENERAL PRECAUTIONS
35.1. SAFETY PRECAUTIONS
35.2. PRECAUTIONS WHEN ATTACHMENTS ARE INSTALLED
36. USING THE BUCKET WITH HOOK
36.1. CHECKING THE BUCKET WITH HOOK ATTACHED FOR DAMAGE
36.2. OPERATIONS THAT SHOULD NOT BE PERFORMED
36.3. PRECAUTIONS DURING OPERATION
37. USING SEAT BELTS
37.1. SEAT BELTS
38. INFORMATION ON OPTIONAL ATTACHMENTS
38.1. INFORMATION ON OPTIONAL ATTACHMENTS
38.2. ATTACHMENT COMBINATION TABLE
38.3. SELECTING TRACKS
38.4. USING RUBBER PAD TRACKS
38.5. USING THE AUTOMATIC LEVELING DEVICE
38.6. USING THE MONOBOOM
38.7. USING VEHICLES TO WHICH ATTACHMENTS CAN BE INSTALLED (MONOBOOM)
38.8. SWITCHING OPERATION PATTERNS (ON MACHINES WHICH HAVE A PATTERN SWITCHING VALVE INSTALLED)

Rate this product