komatsu pc290lci 11e0 pc290nlci 11e0 hydraulic excavator operation and maintenance manual uenam01781 1

komatsu pc290lci 11e0 pc290nlci 11e0 hydraulic excavator operation and maintenance manual uenam01781 2

komatsu pc290lci 11e0 pc290nlci 11e0 hydraulic excavator operation and maintenance manual uenam01781 3

komatsu pc290lci 11e0 pc290nlci 11e0 hydraulic excavator operation and maintenance manual uenam01781 4

komatsu pc290lci 11e0 pc290nlci 11e0 hydraulic excavator operation and maintenance manual uenam01781 5

Komatsu PC290LCi-11E0, PC290NLCi-11E0 Hydraulic Excavator Operation and Maintenance Manual UENAM01781

$20.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: UENAM01781
Format: PDF
Size: 121.9MB
Number of Pages: 511

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- PC290LCi-11E0 Hydraulic Excavator
- PC290NLCi-11E0 Hydraulic Excavator

1. FOREWORD
1.1. READ THIS MANUAL
1.2. KOMATSU MACHINE OPERATOR PRIVACY POLICY
1.3. SAFETY INFORMATION
1.4. INTRODUCTION
1.4.1. intelligent Machine Control
1.4.2. MAIN USE OF MACHINE
1.4.3. DEMOLITION WORK
1.5. ABBREVIATION LIST
1.6. DECLARATION OF CONFORMITY (KUK MANUFACTURE)
1.7. DECLARATION OF CONFORMITY (KLTD MANUFACTURE)
1.8. CONTENTS
2. SAFETY
2.1. SAFETY LABELS
2.1.1. LOCATION OF SAFETY LABELS
2.1.2. SAFETY LABELS
2.2. PRECAUTIONS FOR OPERATION
2.2.1. START ENGINE
2.2.2. PRECAUTIONS RELATED TO CONTROL BOX
2.2.3. PRECAUTIONS RELATED TO SEMIAUTO MODE
2.2.4. PRECAUTIONS FOR TRANSPORTATION
3. OPERATION
3.1. GENERAL VIEW
3.1.1. MACHINE EQUIPMENT NAME
3.1.2. CAB EQUIPMENT NAMES
3.2. EXPLANATION OF COMPONENTS
3.2.1. EXPLANATION OF MACHINE MONITOR EQUIPMENT
3.2.2. SWITCH
3.2.3. CONTROL LEVERS AND PEDALS
3.2.4. intelligent Machine Control SYSTEM
3.2.5. OTHER EQUIPMENT
3.3. MACHINE OPERATIONS AND CONTROLS
3.3.1. CHECKS AND ADJUSTMENT BEFORE STARTING ENGINE
3.3.2. START ENGINE
3.3.3. METHOD FOR STOPPING ENGINE
3.3.4. PROHIBITED OPERATIONS
3.3.5. PARK MACHINE
3.4. HANDLING RADIO
3.5. TRANSPORTATION
3.5.1. REMOVE AND INSTALL GNSS ANTENNA
3.5.2. REMOVE AND INSTALL HANDRAIL
3.5.3. REMOVE AND INSTALL GNSS RADIO ANTENNA AND ANTENNA FOR NETWORK MODEM
3.6. PRECAUTIONS FOR LONGTERM STORAGE
3.6.1. STARTING MACHINE AFTER LONGTERM STORAGE
3.7. TROUBLES AND ACTIONS
3.7.1. IF ERROR INFORMATION IS DISPLAYED ON CONTROL BOX
3.7.2. OTHER TROUBLE
4. MAINTENANCE
4.1. MAINTENANCE SCHEDULE
4.1.1. MAINTENANCE SCHEDULE TABLE
4.2. MAINTENANCE PROCEDURE
4.2.1. EVERY 500 HOURS MAINTENANCE
5. SPECIFICATIONS
5.1. SPECIFICATIONS
5.1.1. SPECIFICATIONS PC290LCI11E0, PC290NLCI11E0
6. ATTACHMENTS AND OPTIONS
6.1. PRECAUTIONS FOR USING ATTACHMENT AND OPTIONS
6.1.1. PRECAUTIONS WHEN SELECTING
6.1.2. READ THE OPERATION AND MAINTENANCE MANUAL THOROUGHLY
6.1.3. PRECAUTIONS WHEN REMOVING AND INSTALLING
6.1.4. PRECAUTIONS FOR USING
6.2. ATTACHMENTS AND OPTIONS
6.2.1. AUTO TILT BUCKET
6.2.2. AUTO TILT BUCKET SETTING
6.2.3. PRECAUTIONS WHEN YOU OPERATE AUTO TILT BUCKET
6.2.4. WORK EQUIPMENT CONTROL OF AUTO TILT BUCKET
6.3. RECOMMENDED ATTACHMENT OPERATIONS
6.3.1. HYDRAULIC BREAKER
7. SETTING
7.1. INTELLIGENT MACHINE CONTROL SETTINGS
7.2. CONTROL BOX
7.2.1. METHOD FOR DISPLAYING MAIN MENU
7.3. MACHINE MONITOR
7.3.1. MACHINE SETTINGS
7.3.2. MC SETTING
8. EXECUTIONS
8.1. SEMIAUTO MODE
8.1.1. PRECAUTIONS FOR OPERATION
8.1.2. PRECAUTIONS FOR REPLACING PARTS AND FAILURES
8.1.3. WORKING MODE
8.1.4. WORKING MODE (WHEN AUTO TILT BUCKET IS EQUIPPED)
8.1.5. SEMIAUTO MODE SETTINGS
8.2. TRAVEL MODE
8.2.1. TRAVEL MODE SETTINGS
8.2.2. DISPLAY OF TRAVEL MODE
8.2.3. OFFSET MENU OF SURFACE
8.2.4. TARGET SURFACE SETTINGS
8.3. ROUGH DIGGING MODE
8.3.1. METHOD FOR SETTING ROUGH DIGGING SCREEN
8.3.2. TEMPORARY DESIGN MENU
8.4. FINE DIGGING MODE
8.4.1. METHOD FOR SETTING FINE DIGGING MODE SCREEN
8.5. TARGET SURFACE SETTINGS
8.5.1. TARGET SURFACE SETTING MENU
8.5.2. METHOD FOR SETTING TARGET SURFACE
8.6. BUCKET EDGE POSITION
8.6.1. DISPLAY BUCKET EDGE POSITION
8.6.2. METHOD FOR COMPARING WITH BENCHMARK
8.6.3. METHOD FOR CORRECTING BUCKET EDGE POSITION
8.7. DAILY CALIBRATION
8.7.1. WALKAROUND CHECKS OF INTELLIGENT MACHINE CONTROL EQUIPMENT
8.8. CHECK GNSS COMMUNICATION STATUS
8.8.1. METHOD FOR CHECKING GNSS COMMUNICATION STATUS
8.8.2. METHOD FOR CHECKING NUMBER OF SATELLITES AND ERROR OF POSITIONING
8.8.3. METHOD FOR DISPLAYING BUCKET EDGE COORDINATES
8.8.4. METHOD FOR SETTING SATELLITE POSITION DISPLAY AND ELEVATION ANGLE
8.8.5. METHOD FOR DISPLAYING GNSS RECEIVER INFORMATION
8.8.6. METHOD FOR CHEKING EXPECTANCY OF EDGE ACCURANCY
8.8.7. SET SATELLITE
8.8.8. METHOD FOR SETTING GLONASS SATELLITE
8.8.9. METHOD FOR SETTING TILT SENSOR MODE
8.9. USE OF TOPO SURVEY
8.9.1. METHOD FOR PERFORMING TOPO SURVEY MANUALLY
8.9.2. METHOD FOR PERFORMING AUTOTOPO SURVEY
8.9.3. METHOD FOR CANCELING TOPOGRAPHIC SURVEYS
8.10. TROUBLESHOOTING
8.10.1. CONTROL BOX SCREEN DISPLAY
8.10.2. SEMIAUTO MODE
8.10.3. WORKING ACCURACY
8.10.4. AUTO TILT BUCKET
9. INDEX

Rate this product