komatsu pc360lci 11e0 pc360nlci 11e0 hydraulic excavator operation and maintenance manual uenam01701 1

komatsu pc360lci 11e0 pc360nlci 11e0 hydraulic excavator operation and maintenance manual uenam01701 2

komatsu pc360lci 11e0 pc360nlci 11e0 hydraulic excavator operation and maintenance manual uenam01701 3

komatsu pc360lci 11e0 pc360nlci 11e0 hydraulic excavator operation and maintenance manual uenam01701 4

komatsu pc360lci 11e0 pc360nlci 11e0 hydraulic excavator operation and maintenance manual uenam01701 5

Komatsu PC360LCi-11E0, PC360NLCi-11E0 Hydraulic Excavator Operation and Maintenance Manual UENAM01701

$20.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: UENAM01701
Format: PDF
Size: 120.0MB
Number of Pages: 500

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- PC360LCi-11E0 Hydraulic Excavator
- PC360NLCi-11E0 Hydraulic Excavator

1. FOREWORD
1.1. READ THIS MANUAL
1.2. KOMATSU MACHINE OPERATOR PRIVACY POLICY
1.3. SAFETY INFORMATION
1.4. INTRODUCTION
1.4.1. intelligent Machine Control
1.4.2. MAIN USE OF MACHINE
1.4.3. DEMOLITION WORK
1.5. ABBREVIATION LIST
1.6. DECLARATION OF CONFORMITY (KUK MANUFACTURE)
1.7. DECLARATION OF CONFORMITY (KLTD MANUFACTURE)
1.8. CONTENTS
2. SAFETY
2.1. SAFETY LABELS
2.1.1. LOCATION OF SAFETY LABELS
2.1.2. SAFETY LABELS
2.2. PRECAUTIONS FOR OPERATION
2.2.1. START ENGINE
2.2.1.1. CHECKS AND ADJUSTMENT BEFORE STARTING ENGINE
2.2.2. PRECAUTIONS RELATED TO CONTROL BOX
2.2.3. PRECAUTIONS RELATED TO SEMIAUTO MODE
2.2.4. PRECAUTIONS FOR TRANSPORTATION
2.2.4.1. PRECAUTIONS WHEN LOADING AND UNLOADING
3. OPERATION
3.1. GENERAL VIEW
3.1.1. MACHINE EQUIPMENT NAME
3.1.2. CAB EQUIPMENT NAMES
3.2. EXPLANATION OF COMPONENTS
3.2.1. EXPLANATION OF MACHINE MONITOR EQUIPMENT
3.2.1.1. WARNING DISPLAY
3.2.1.2. ACTION LEVEL DISPLAY
3.2.1.3. Intelligent Machine Control SYSTEM STATE CAUTION LAMP
3.2.1.4. CALIBRATION STATE CAUTION LAMP
3.2.1.5. IMU STATE CAUTION LAMP
3.2.1.6. CYLINDER FUNCTION STATE CAUTION LAMP
3.2.1.7. Intelligent Machine Control EQUIPMENT STATE CAUTION LAMP
3.2.1.8. PILOT DISPLAY AND METER DISPLAY
3.2.2. SWITCH
3.2.2.1. LAMP SWITCH
3.2.2.2. BOOM SECONDARY DRIVE SWITCH
3.2.2.3. AUTO/MANUAL SWITCH
3.2.3. CONTROL LEVERS AND PEDALS
3.2.3.1. LOCK LEVER
3.2.4. intelligent Machine Control SYSTEM
3.2.4.1. CONTROL BOX
3.2.5. OTHER EQUIPMENT
3.2.5.1. METHOD FOR OPENING AND CLOSING CAB FRONT WINDOW
3.2.5.2. CUP HOLDER
3.2.5.3. POWER SUPPLY OUTLET
3.2.5.4. FUSE
3.2.5.5. METHOD FOR REMOVING AND INSTALLING CONTROL BOX
3.2.5.6. HANDLING EXTERNAL RADIO, MODEM AND CONTROLLER
3.3. MACHINE OPERATIONS AND CONTROLS
3.3.1. CHECKS AND ADJUSTMENT BEFORE STARTING ENGINE
3.3.1.1. METHOD FOR WALKAROUND CHECK
3.3.1.2. METHOD FOR ADJUSTING
3.3.2. START ENGINE
3.3.2.1. START CONTROL BOX
3.3.2.2. METHOD FOR SHUTTING DOWN CONTROL BOX
3.3.3. METHOD FOR STOPPING ENGINE
3.3.4. PROHIBITED OPERATIONS
3.3.4.1. PROHIBITION OF OPERATIONS USING HYDRAULIC CYLINDERS TO STROKE END
3.3.5. PARK MACHINE
3.4. HANDLING RADIO
3.5. TRANSPORTATION
3.5.1. REMOVE AND INSTALL GNSS ANTENNA
3.5.1.1. METHOD FOR REMOVING GNSS ANTENNA
3.5.1.2. METHOD FOR INSTALLING GNSS ANTENNA
3.5.2. REMOVE AND INSTALL HANDRAIL
3.5.2.1. METHOD FOR REMOVING HANDRAIL
3.5.2.2. METHOD FOR INSTALLING HANDRAIL
3.5.3. REMOVE AND INSTALL GNSS RADIO ANTENNA AND ANTENNA FOR NETWORK MODEM
3.5.3.1. METHOD FOR REMOVING GNSS RADIO ANTENNA AND ANTENNA FOR NETWORK MODEM
3.5.3.2. METHOD FOR INSTALLING GNSS RADIO ANTENNA AND ANTENNA FOR NETWORK MODEM
3.6. PRECAUTIONS FOR LONGTERM STORAGE
3.6.1. STARTING MACHINE AFTER LONGTERM STORAGE
3.7. TROUBLES AND ACTIONS
3.7.1. IF ERROR INFORMATION IS DISPLAYED ON CONTROL BOX
3.7.1.1. IF Initializing IS DISPLAYED
3.7.2. OTHER TROUBLE
3.7.2.1. IF MACHINE MONITOR SHOWS WARNING DISPLAY
3.7.2.2. PHENOMENA AND ACTIONS FOR CONTROL BOX
4. MAINTENANCE
4.1. MAINTENANCE SCHEDULE
4.1.1. MAINTENANCE SCHEDULE TABLE
4.2. MAINTENANCE PROCEDURE
4.2.1. EVERY 500 HOURS MAINTENANCE
4.2.1.1. METHOD OF CHECKING LOOSENESS OF BUCKET CYLINDER STROKE SENSOR WIRING HARNESS CLAMP, HARDENING OF RUBBER
4.2.1.2. METHOD OF CHECKING AND CLEANING CYLINDER STROKE SENSOR CASE BOLT
5. SPECIFICATIONS
5.1. SPECIFICATIONS
5.1.1. SPECIFICATIONS PC360LCI11E0, PC360NLCI11E0
6. ATTACHMENTS AND OPTIONS
6.1. PRECAUTIONS FOR USING ATTACHMENT AND OPTIONS
6.1.1. PRECAUTIONS WHEN SELECTING
6.1.2. READ THE OPERATION AND MAINTENANCE MANUAL THOROUGHLY
6.1.3. PRECAUTIONS WHEN REMOVING AND INSTALLING
6.1.4. PRECAUTIONS FOR USING
6.2. ATTACHMENTS AND OPTIONS
6.2.1. AUTO TILT BUCKET
6.2.2. AUTO TILT BUCKET SETTING
6.2.3. PRECAUTIONS WHEN YOU OPERATE AUTO TILT BUCKET
6.2.4. WORK EQUIPMENT CONTROL OF AUTO TILT BUCKET
6.3. RECOMMENDED ATTACHMENT OPERATIONS
6.3.1. HYDRAULIC BREAKER
7. SETTING
7.1. INTELLIGENT MACHINE CONTROL SETTINGS
7.2. CONTROL BOX
7.2.1. METHOD FOR DISPLAYING MAIN MENU
7.2.1.1. MAIN MENU DISPLAY
7.2.1.2. PROJECT FILE SETTING AND EDITING
7.2.1.3. GUIDANCE SETTINGS
7.2.1.4. DISPLAY OPTIONS
7.2.1.5. KOMATSU OPTIONS
7.2.1.6. TOOLS
7.2.1.7. MACHINE SETTING
7.2.1.8. METHOD FOR SETTING GNSS RADIO DEVICE
7.2.1.9. PREPARATIONS FOR CALIBRATION
7.2.1.10. BUCKET CONFIGURATION
7.2.1.11. METHOD FOR SETTING SHORTCUTS MENU
7.3. MACHINE MONITOR
7.3.1. MACHINE SETTINGS
7.3.1.1. ATTACHMENT SETTING
7.3.1.2. PROPORTIONAL SETTING
7.3.2. MC SETTING
7.3.2.1. IMU ADJUSTMENT
7.3.2.2. BUCKET WEIGHT SETTING
7.3.2.3. BOOM FINE CONTROL ADJUSTMENT
7.3.2.4. SEMIAUTO ADJUSTMENT
8. EXECUTIONS
8.1. SEMIAUTO MODE
8.1.1. PRECAUTIONS FOR OPERATION
8.1.2. PRECAUTIONS FOR REPLACING PARTS AND FAILURES
8.1.3. WORKING MODE
8.1.4. WORKING MODE (WHEN AUTO TILT BUCKET IS EQUIPPED)
8.1.5. SEMIAUTO MODE SETTINGS
8.1.5.1. CHANGE TO SEMIAUTO MODE
8.1.5.2. LIST OF RESTRICTED ITEMS DURING SEMIAUTO MODE
8.1.5.3. METHOD FOR ADJUSTING CONTROL SURFACE OFFSET
8.1.5.4. METHOD FOR SWITCHING TO MANUAL MODE
8.2. TRAVEL MODE
8.2.1. TRAVEL MODE SETTINGS
8.2.2. DISPLAY OF TRAVEL MODE
8.2.3. OFFSET MENU OF SURFACE
8.2.4. TARGET SURFACE SETTINGS
8.2.4.1. METHOD FOR SETTING TARGET SURFACE
8.2.4.2. METHOD FOR RESETTING TARGET SURFACE
8.3. ROUGH DIGGING MODE
8.3.1. METHOD FOR SETTING ROUGH DIGGING SCREEN
8.3.2. TEMPORARY DESIGN MENU
8.3.2.1. METHOD FOR CREATING TEMPORARY DESIGN SURFACE
8.4. FINE DIGGING MODE
8.4.1. METHOD FOR SETTING FINE DIGGING MODE SCREEN
8.5. TARGET SURFACE SETTINGS
8.5.1. TARGET SURFACE SETTING MENU
8.5.2. METHOD FOR SETTING TARGET SURFACE
8.6. BUCKET EDGE POSITION
8.6.1. DISPLAY BUCKET EDGE POSITION
8.6.1.1. METHOD FOR SETTING MEASURED BUCKET EDGE POSITION
8.6.1.2. DISPLAY BUCKET EDGE COORDINATES
8.6.1.3. DISPLAY DISTANCE BETWEEN BUCKET EDGE AND DESIGN SURFACE
8.6.1.4. DISPLAY BUCKET EDGE POSITION ALGNMENT STATION
8.6.1.5. DISPLAY DISTANCE BETWEEN CENTER LINE AND BUCKET EDGE POSITION
8.6.1.6. METHOD FOR MEASURING BUCKET EDGE POSITION
8.6.1.7. METHOD FOR SAVING MEASURED DATA
8.6.2. METHOD FOR COMPARING WITH BENCHMARK
8.6.3. METHOD FOR CORRECTING BUCKET EDGE POSITION
8.7. DAILY CALIBRATION
8.7.1. WALKAROUND CHECKS OF INTELLIGENT MACHINE CONTROL EQUIPMENT
8.7.1.1. METHOD FOR CHECKING GNSS ANTENNA AND CABLE
8.7.1.2. METHOD FOR CHECKING GNSS RADIO DEVICE
8.7.1.3. METHOD FOR CHECKING LOOSENESS OF CONTROL BOX
8.7.1.4. METHOD FOR CHECKS BEFORE STARTING ON intelligent Machine Control EQUIPMENT
8.7.1.5. METHOD FOR CHECKING PROJECT FILE
8.7.1.6. METHOD FOR CHECKING GNSS COMMUNICATION STATUS
8.7.1.7. METHOD FOR CHECKING CONTROL BOX SCREEN DISPLAY
8.7.1.8. METHOD FOR CHECKING AND ADJUSTING BUCKET EDGE ACCURACY
8.7.1.9. METHOD FOR CALIBRATING BUCKET TOOTH
8.8. CHECK GNSS COMMUNICATION STATUS
8.8.1. METHOD FOR CHECKING GNSS COMMUNICATION STATUS
8.8.2. METHOD FOR CHECKING NUMBER OF SATELLITES AND ERROR OF POSITIONING
8.8.3. METHOD FOR DISPLAYING BUCKET EDGE COORDINATES
8.8.4. METHOD FOR SETTING SATELLITE POSITION DISPLAY AND ELEVATION ANGLE
8.8.5. METHOD FOR DISPLAYING GNSS RECEIVER INFORMATION
8.8.6. METHOD FOR CHEKING EXPECTANCY OF EDGE ACCURANCY
8.8.7. METHOD FOR SETTING GLONASS SATELLITE
8.8.8. METHOD FOR SETTING TILT SENSOR
8.9. USE OF TOPO SURVEY
8.9.1. METHOD FOR PERFORMING TOPO SURVEY MANUALLY
8.9.1.1. CREATE NEW LAYER TO RECORD DATA
8.9.1.2. METHOD FOR INPUTTING NEW POSITION DETAILS NAME
8.9.2. METHOD FOR PERFORMING AUTOTOPO SURVEY
8.9.2.1. METHOD FOR CREATING NEW LAYER TO RECORD DATA
8.9.2.2. METHOD FOR INPUTTING NEW POSITION DETAILS NAME
8.9.3. METHOD FOR CANCELING TOPOGRAPHIC SURVEYS
8.10. TROUBLESHOOTING
8.10.1. CONTROL BOX SCREEN DISPLAY
8.10.2. SEMIAUTO MODE
8.10.3. WORKING ACCURACY
8.10.4. AUTO TILT BUCKET
9. INDEX

Rate this product