Komatsu WA320-1LC Wheel Loader Operation and Maintenance Manual CEAMW19021

Komatsu WA320-1LC Wheel Loader Operation and Maintenance Manual CEAMW19021 - Image 2

Komatsu WA320-1LC Wheel Loader Operation and Maintenance Manual CEAMW19021 - Image 3

Komatsu WA320-1LC Wheel Loader Operation and Maintenance Manual CEAMW19021 - Image 4

Komatsu WA320-1LC Wheel Loader Operation and Maintenance Manual CEAMW19021 - Image 5

komatsu wa320 1lc wheel loader operation and maintenance manual ceamw19021 2

komatsu wa320 1lc wheel loader operation and maintenance manual ceamw19021 3

Komatsu WA320-1LC Wheel Loader Operation and Maintenance Manual CEAMW19021

$20.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: CEAMW19021
Format: PDF
Size: 13.4MB
Number of Pages: 211

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- WA320-1LC Wheel Loader

1. MAIN MENU
2. FOREWORD
3. INTRODUCTION
3.1. SAFETY INFORMATION
3.2. BREAKING IN THE NEW MACHINE
3.3. MACHINE AND ENGINE SERIAL NUMBERS
3.4. QUICK REFERENCE INFORMATION
3.5. CONTENTS
4. SAFETY PRECAUTIONS SECTION 1
4.1. GENERAL PRECAUTIONS
4.1.1. PERSONNEL PRECAUTIONS
4.1.2. MACHINE PRECAUTIONS
4.2. OPERATION
4.2.1. BEFORE STARTING
4.2.2. STARTUP
4.2.3. GENERAL OPERATING PRECAUTIONS
4.2.4. DRIVING THE MACHINE
4.2.5. OPERATING THE ATTACHMENTS
4.2.6. PULLING/TOWING
4.2.7. SHUTDOWN
4.3. MAINTENANCE
4.3.1. GENERAL MACHINE PRECAUTIONS
4.3.2. GENERAL WORK PRECAUTIONS
4.4. SAFETY PRODUCT GRAPHICS AND LOCATIONS
4.4.1. BEFORE CARRYING OUT MAINTENANCE
5. OPERATION SECTION 2
5.1. GENERAL VIEW
5.2. INSTRUMENTS AND CONTROLS
5.2.1. MONITOR PANEL
5.2.2. SWITCHES
5.2.3. LEVERS AND PEDALS
5.2.4. CAB DOOR HOLD OPEN LOCK IF EQUIPPED
5.2.5. AIR CLEANER SERVICE INDICATOR
5.2.6. FRAME LOCKING BAR
5.2.7. HOOD TILT LOCK
5.2.8. MAIN CIRCUIT
5.2.9. FUSE BOXES
5.2.10. OPERATORS SEAT
5.2.11. RIGHT SIDE ARMREST
5.2.12. SEAT BELT
5.3. DRAWBAR PIN
5.4. CAB HEATER AND DEFROSTER
5.4.1. CONTROL PANEL
5.4.2. CONTROL PANEL
5.4.3. METHOD OF OPERATION
5.5. CAB HEATER, DEFROSTER AND AIR CONDITIONER IF EQUIPPED
5.5.1. CONTROL PANEL
5.5.2. METHOD OF OPERATION
5.6. LOCKING FILLER CAPS
5.6.1. FUEL TANK FILLER CAP
5.6.2. HYDRAULIC TANK FILLER CAP
5.7. CHECK BEFORE STARTING
5.7.1. WALKAROUND CHECK
5.7.2. CHECK MONITOR PANEL
5.7.3. CHECK AND REFILL COOLANT
5.7.4. CHECK AIR CLEANER SERVICE INDICATOR
5.7.5. CHECK OIL LEVEL AND REFILL IN ENGINE OIL PAN
5.7.6. CHECK FUEL LEVEL AND REFILL FUEL
5.7.7. DRAIN THE WATER FROM THE FUELWATER SEPARATOR
5.7.8. ADDITIONAL CHECKS
5.7.9. CHECK ELECTRICAL WIRING
5.8. OPERATING YOUR MACHINE
5.8.1. BEFORE STARTING THE ENGINE
5.8.2. STARTING ENGINE
5.8.3. COLD WEATHER STARTING
5.8.4. COLD WEATHER WARMUP PROCEDURE
5.8.5. CHECKS AFTER STARTING
5.8.6. MOVING MACHINE OFF
5.8.7. SHIFTING GEAR
5.8.8. SHIFTING BETWEEN FORWARD AND REVERSE
5.8.9. STEERING MACHINE
5.8.10. TO STOP THE MACHINE
5.8.11. TO STOP THE ENGINE
5.8.12. OPERATIONS AFTER STOPPING ENGINE
5.8.13. OPERATIONAL PRECAUTIONS
5.8.14. PRECAUTIONS WHEN DRIVING UP OR DOWN SLOPES
5.8.15. PARKING MACHINE
5.9. ADJUSTMENT OF WORK EQUIPMENT
5.9.1. ADJUSTING BOOM KICKOUT
5.9.2. ADJUSTING BUCKET POSITIONER
5.9.3. BUCKET LEVEL INDICATOR
5.10. HANDLING TIRES
5.10.1. PRECAUTIONS WHEN HANDLING TIRES
5.10.2. PRECAUTIONS WHEN DRIVING MACHINE
5.10.3. TIRE PRESSURE
5.11. TOWING
5.11.1. TOWING THE MACHINE
5.12. TRANSPORTATION
5.13. COLD WEATHER OPERATION
5.13.1. PREPARATION FOR LOW TEMPERATURE
5.13.2. CAUTIONS AFTER COMPLETION OF WORK
5.14. AFTER COLD WEATHER
5.15. LONG TERM STORAGE
5.15.1. BEFORE STORAGE
5.15.2. DURING STORAGE
5.15.3. AFTER STORAGE
5.16. HANDLING OF BATTERY
5.16.1. PRECAUTIONS FOR CHARGING BATTERY
5.16.2. REMOVAL AND INSTALLATION OF BATTERY
5.16.3. STARTING ENGINE WITH BOOSTER CABLES
5.17. TROUBLESHOOTING
5.17.1. ELECTRICAL SYSTEM
6. MAINTENANCE SECTION 3
6.1. PERIODIC MAINTENANCE
6.2. MAINTENANCE GUIDELINES
6.3. OUTLINES OF SERVICE
6.3.1. LUBRICATION WHEN SHIPPED
6.3.2. RELATING TO ENGINE
6.3.3. RELATING TO HYDRAULIC SYSTEM
6.3.4. RELATING TO ELECTRICAL SYSTEM
6.3.5. RELATING TO LUBRICATION
6.3.6. BLEEDING AIR
6.4. WEAR PARTS REPLACEMENT
6.5. PERIODICAL PART REPLACEMENT
6.6. LUBRICANTS, FUEL AND COOLANT
6.6.1. PROPER SELECTION TABLE
6.7. SCHEDULED MAINTENANCE GUIDE
6.8. OIL FILLER AND LEVEL GAUGE POSITIONS
6.9. INITIAL 250 HOURS SERVICE ONLY
6.9.1. TRANSMISSION OIL FILTER
6.10. WHEN REQUIRED
6.10.1. COOLANT ADDITIVE CONCENTRATION DCA4
6.10.2. AIR CLEANER ELEMENT
6.10.3. TRANSMISSION OIL
6.10.4. RADIATOR CORE
6.10.5. WINDSHIELD WASHER TANKS
6.10.6. DRIVE AXLE OIL
6.10.7. DRIVE AXLE HOUSING BREATHERS
6.10.8. LUBRICATING
6.10.9. BUCKET BOLTON CUTTlNG EDGE IF EQUIPPED
6.10.10. BUCKET TEETH IF EQUIPPED
6.10.11. PARKING BRAKE
6.10.12. LENGTH OF LEVER
6.10.13. AIR CONDITIONER CONDENSER IF EQUIPPED
6.10.14. AIR CONDITIONER REFRIGERANT CHARGE IF EQUIPPED
6.10.15. STEERING
6.10.16. HYDRAULIC SYSTEM
6.10.17. SERVICE METER
6.11. CHECK BEFORE STARTING
6.12. EVERY 50 HOURS SERVICE
6.12.1. FUEL TANK
6.12.2. TIRES
6.13. EVERY 100 HOURS SERVICE
6.13.1. HYDRAULIC TANK
6.13.2. LUBRICATING
6.13.3. CAB AIR FILTER IF EQUIPPED
6.13.4. AIR CONDITIONER FILTER IF EQUIPPED
6.13.5. TRANSMISSION CASE
6.14. EVERY 250 HOURS SERVICE
6.14.1. LUBRICATING
6.14.2. WHEEL HUB BOLTS
6.14.3. ENGINE OIL PAN AND FILTER
6.14.4. BATTERY ELECTROLYTE
6.14.5. AIR INTAKE SYSTEM
6.14.6. AIR CONDITIONER COMPRESSOR DRIVE BELT IF EQUIPPED
6.14.7. COOLANT FILTER
6.15. EVERY 500 HOURS SERVICE
6.15.1. LUBRICATING
6.15.2. FUEL FILTERS
6.15.3. TRANSMISSION OIL FILTER
6.15.4. ANTIFREEZE CONCENTRATION
6.15.5. AIR DRYER IF EQUIPPED
6.16. EVERY 1000 HOURS SERVICE
6.16.1. LUBRICATING
6.16.2. TRANSMISSION CASE BREATHER
6.16.3. TRANSMISSION OIL AND STRAINER
6.16.4. ENGINE VALVES
6.16.5. DRIVE BELT
6.16.6. DRIVE BELT, TENSIONER BEARING AND FAN HUB
6.17. EVERY 2000 HOURS SERVICE
6.17.1. DRIVE AXLES
6.17.2. HYDRAULIC TANK BREATHER
6.17.3. HYDRAULIC TANK AND FILTER
6.17.4. BRAKE DISC
6.17.5. VIBRATION DAMPER
6.17.6. COOLING SYSTEM
6.17.7. AIR CONDITIONER FILTER IF EQUIPPED
6.17.8. ACCUMULATOR
7. SPECIFICATIONS SECTION 4
7.1. GENERAL SPECIFICATIONS
7.2. STANDARD TIGHTENING TORQUES
7.2.1. STANDARD TIGHTENING TORQUE OF BOLTS AND NUTS
7.2.2. TIGHTENING TORQUE OF SPLIT FLANGE BOLTS
7.2.3. TIGHTENING TORQUE FOR NUTS OF FLARED FllTlNGS
7.3. UNIT CONVERSIONS
7.3.1. AREA
7.3.2. DENSITY (Mass Density)
7.3.3. FORCE
7.3.4. FORCE PER LENGTH
7.3.5. TEMPERATURE INTERVAL OR TOLERANCE
7.3.6. VOLUME
7.3.7. TORQUE
7.3.8. VELOCITY

Rate this product