komatsu wa600 6 wheel loader operation and maintenance manual eeam024501 1

komatsu wa600 6 wheel loader operation and maintenance manual eeam024501 2

komatsu wa600 6 wheel loader operation and maintenance manual eeam024501 3

komatsu wa600 6 wheel loader operation and maintenance manual eeam024501 4

komatsu wa600 6 wheel loader operation and maintenance manual eeam024501 5

Komatsu WA600-6 Wheel Loader Operation and Maintenance Manual EEAM024501

$20.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: EEAM024501
Format: PDF
Size: 21.0MB
Number of Pages: 420

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- WA600-6 Wheel Loader

1. FOREWORD
1.1. FOREWORD
1.2. SAFETY INFORMATION
1.2.1. Noise emission levels
1.2.2. Vibration levels
1.3. INTRODUCTION
1.3.1. FRONT/REAR, LEFT/RIGHT DIRECTIONS OF MACHINE
1.3.2. VISIBILITY FROM OPERATORS SEAT
1.4. NECESSARY INFORMATION
1.4.1. PRODUCT IDENTIFICATION NUMBER (PIN)/MACHINE SERIAL NO. PLATE
1.4.2. EPA REGULATIONS, ENGINE NUMBER PLATE
1.4.3. POSITION OF SERVICE METER
1.4.4. TABLE TO ENTER SERIAL NO. AND DISTRIBUTOR
1.4.5. MACHINE SERIAL NUMBER PLATE
1.4.6. ATTACHMENTS, OPTIONS
1.4.7. LOCATION OF SAFETY LABELS
1.4.8. SAFETY LABELS
1.5. GENERAL PRECAUTIONS
1.6. PRECAUTIONS FOR OPERATION
1.6.1. STARTING ENGINE
1.6.2. OPERATION
1.6.3. TRANSPORTATION
1.6.4. BATTERY
1.6.5. TOWING
1.7. PRECAUTIONS FOR MAINTENANCE
1.8. PRECAUTIONS WITH TIRES
2. OPERATION
2.1. GENERAL VIEW
2.1.1. GENERAL VIEW OF MACHINE
2.1.2. GENERAL VIEW OF CONTROLS AND GAUGES
2.2. EXPLANATION OF COMPONENTS
2.2.1. MACHINE MONITOR
2.2.2. SWITCHES
2.2.3. CONTROL LEVERS, PEDALS
2.2.4. CAP WITH LOCK
2.2.5. FRAME LOCK BAR
2.2.6. TOWING PIN
2.2.7. BACKUP ALARM
2.2.8. OPENING CAB, WINDOW DOOR
2.2.9. HANDLING CAB WIPER
2.2.10. DUST INDICATOR
2.2.11. FUSE
2.2.12. CIRCUIT BREAKER
2.2.13. SLOW BLOW FUSE
2.2.14. LUNCH BOX TRAY
2.2.15. TOOL BOX
2.2.16. GREASE PUMP
2.2.17. LOCATION OF FIRE EXTINGUISHER
2.2.18. POWER OUTLET
2.2.19. AM/FM RADIOCASSETTE STEREO
2.2.20. AIR CONDITIONER
2.3. OPERATION
2.3.1. CHECK BEFORE STARTING ENGINE, ADJUST
2.3.2. STARTING ENGINE
2.3.3. OPERATIONS AND CHECKS AFTER STARTING ENGINE
2.3.4. STOPPING ENGINE
2.3.5. CHECK AFTER STOPPING ENGINE
2.3.6. MOVING THE MACHINE (DIRECTIONAL, SPEED), STOPPING THE MACHINE
2.3.7. TURNING
2.3.8. OPERATION OF WORK EQUIPMENT
2.3.9. SEMI AUTO DIGGING OPERATIONS
2.3.10. REMOTE POSITIONER
2.3.11. WORK POSSIBLE USING WHEEL LOADER
2.3.12. PRECAUTIONS FOR OPERATION
2.3.13. REMOVAL AND INSTALLATION OF THE BUCKET
2.3.14. PARKING MACHINE
2.3.15. CHECKS AFTER COMPLETION OF OPERATION
2.3.16. LOCKING
2.3.17. HANDLING THE TIRES
2.4. TRANSPORTATION
2.4.1. TRANSPORTATION PROCEDURE
2.4.2. LOADING, UNLOADING WORK
2.4.3. METHOD OF SECURING MACHINE
2.4.4. METHOD OF LIFTING MACHINE
2.4.5. PRECAUTIONS WHEN DISASSEMBLY OR REASSEMBLING WORK EQUIPMENT
2.5. COLD WEATHER OPERATION
2.5.1. PRECAUTIONS FOR LOW TEMPERATURE
2.5.2. PRECAUTIONS AFTER COMPLETION OF WORK
2.5.3. AFTER COLD WEATHER
2.5.4. WARMINGUP OPERATION FOR STEERING HYDRAULIC CIRCUIT IN COLD WEATHER
2.6. LONGTERM STORAGE
2.6.1. BEFORE STORAGE
2.6.2. DURING STORAGE
2.6.3. AFTER STORAGE
2.7. TROUBLESHOOTING
2.7.1. WHEN MACHINE RUNS OUT OF FUEL
2.7.2. METHOD OF TOWING MACHINE
2.7.3. IF BATTERY IS DISCHARGED
2.7.4. METHOD FOR LOWERING WORK EQUIPMENT WHEN ENGINE HAS STOPPED
2.7.5. OTHER TROUBLE
3. MAINTENANCE
3.1. GUIDES TO MAINTENANCE
3.2. OUTLINES OF SERVICE
3.2.1. HANDLING OIL, FUEL, COOLANT, AND PERFORMING OIL CLINIC
3.2.2. OUTLINE OF ELECTRIC SYSTEM
3.3. WEAR PARTS
3.3.1. WEAR PARTS LIST
3.4. RECOMMENDED FUEL, COOLANT, AND LUBRICANT
3.4.1. USE OF FUEL, COOLANT AND LUBRICANTS ACCORDING TO AMBIENT TEMPERATURE
3.4.2. RECOMMENDED BRANDS, RECOMMENDED QUALITY FOR PRODUCTS OTHER THAN KOMATSU GENUINE OIL
3.5. STANDARD TIGHTENING TORQUES FOR BOLTS AND NUTS
3.5.1. TORQUE LIST
3.6. PERIODIC REPLACEMENT OF SAFETY CRITICAL PARTS
3.6.1. SAFETY CRITICAL PARTS
3.7. MAINTENANCE SCHEDULE CHART
3.7.1. MAINTENANCE SCHEDULE CHART
3.8. SERVICE PROCEDURE
3.8.1. INITIAL 10 HOURS SERVICE (SERVICE FOR FIRST 50 HOURS ON NEW MACHINE)
3.8.2. INITIAL 250 HOURS SERVICE
3.8.3. WHEN REQUIRED
3.8.4. CHECK BEFORE STARTING
3.8.5. EVERY 50 HOURS SERVICE
3.8.6. EVERY 100 HOURS SERVICE
3.8.7. EVERY 250 HOURS SERVICE
3.8.8. EVERY 500 HOURS SERVICE
3.8.9. EVERY 1000 HOURS SERVICE
3.8.10. EVERY 2000 HOURS SERVICE
3.8.11. EVERY 4000 HOURS SERVICE
3.8.12. EVERY 8000 HOURS SERVICE
4. SPECIFICATIONS
4.1. SPECIFICATIONS
5. ATTACHMENTS, OPTIONS
5.1. HANDLING STEERING WHEEL SPECIFICATION MACHINE
5.1.1. EXPLANATION OF COMPONENTS
5.1.2. FUNCTIONS OF STEERING WHEEL SPECIFICATION MACHINE
5.2. SELECTING BUCKET AND TIRES
5.3. STARTING IN COLD AREAS
5.3.1. ELECTRIC HEATER
5.4. HANDLING LOAD METER
5.4.1. OUTLINE OF LOAD METER
5.4.2. PRINCIPLE OF LOAD METER MEASUREMENT
5.4.3. POINTS TO REMEMBER TO ENSURE HIGH ACCURACY
5.4.4. USING LOAD METER
5.5. HANDLING AUTOGREASING SYSTEM
5.5.1. METHOD OF OPERATING AUTOGREASING SYSTEM
5.5.2. PRECAUTIONS WHEN HANDLING AUTOGREASING SYSTEM
5.5.3. TROUBLESHOOTING
5.6. HANDLING BATTERY DISCONNECTOR SWITCH
5.6.1. EXPLANATION OF COMPONENTS
5.6.2. HANDLING
5.7. HANDLING STARTING AID CONNECTOR
5.7.1. STARTING ENGINE WHEN USING STARTING AID CONNECTOR
5.8. HANDLING REAR FENDER
5.8.1. HANDLING
5.9. HANDLING MACHINES EQUIPPED WITH VHMS
5.9.1. VHMS INSTALLED, COMMUNICATIONS TERMINAL NOT INSTALLED
5.9.2. VHMS AND COMMUNICATIONS TERMINAL INSTALLED

Rate this product