komatsu wd600 6r wheel dozer field assembly manual gen00143 03 1

komatsu wd600 6r wheel dozer field assembly manual gen00143 03 2

komatsu wd600 6r wheel dozer field assembly manual gen00143 03 3

komatsu wd600 6r wheel dozer field assembly manual gen00143 03 4

komatsu wd600 6r wheel dozer field assembly manual gen00143 03 5

Komatsu WD600-6R Wheel Dozer Field Assembly Manual GEN00143-03

$20.00

Type Of Manual: Field Assembly Manual
Manual ID: GEN00143-03
Format: PDF
Size: 11.2MB
Number of Pages: 83

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- WD600-6R Wheel Dozer

1. Block outline (for principal components only)
2. Principal component dimension table
3. Work space layout
4. General assembly schedule
5. List of equipment, jigs, tools and consumables
6. Oil, grease and paints
7. Assembly procedure
7.1. Oil and coolant
7.2. Oil and coolant capacity
7.3. Setting the front axle and bare machine to stationary position
7.4. Installing the front axle
7.5. Connecting the drive shaft
7.6. Connecting the brake pipe
7.7. Connecting the brake pipe (Brake cooling specification)
7.8. Installing tire and rim assembly
7.9. Installing step
7.10. Installing cab (1)
7.11. Installing cab (2) (AJSS specification)
7.12. Installing cab (2) (Steering wheel specification)
7.13. Installing cab (2) (AJSS and steering wheel specification)
7.14. Installing cab (3)
7.15. Installing cab (4) (AJSS specification)
7.16. Installing cab (4) (Steering wheel specification)
7.17. Installing cab (5) (Steering wheel specification)
7.18. Installing cab (6) (AJSS and steering wheel specification)
7.19. Installing cab harness (1/3)
7.20. Installing cab harness (2/3)
7.21. Installing cab harness (3/3) (Steering wheel specification)
7.22. Installing cab duct (1/3)
7.23. Installing cab duct (2/3)
7.24. Installing cab duct (3/3)
7.25. Installation of yellow rotary lamp
7.26. Installing front fender
7.27. Installing front light support and connection
7.28. Installing muffler stack and mirror
7.29. Installing rear access ladder and L.H. platform
7.30. Installing the left handrail
7.31. Installing right platform and R.H. handrail
7.32. Installing fire extinguisher
7.33. Installing the rear fender mudguard plate
7.34. Installing rear fender
7.35. Installing cab undercover
7.36. Checking of sections
7.37. Air bleeding of work equipment hydraulic circuit and respective cylinders
7.38. Starting engine (1/2)
7.39. Starting engine (2/2)
7.40. Bleeding air from brake system
7.41. Installation of Hlink and Ylink
7.42. Installation of right and left support assemblies
7.43. Installation of right and left frame assemblies
7.44. Installation of blade assembly (1/2)
7.45. Installation of blade assembly (2/2)
7.46. Work equipment greasing (1st time)
7.47. Setting machine monitor
7.48. Work equipment calibration1, Outline and selection of service mode
7.49. Work equipment calibration2, Display of service mode (reference)
7.50. Work equipment calibration3, Work equipment EPC starting point correction1 (LOWER)
7.51. Work equipment calibration4, Work equipment EPC starting point correction2 (RAISE)
7.52. Work equipment calibration5, Work equipment control lever detent position correction
7.53. Work equipment calibration6, Pitching flow correction
7.54. Deleting the electrical system failure history (1/2)
7.55. Deleting the electrical system failure history (2/2)
7.56. Installing the floor mat (AJSS specification)
7.57. Installing the floor mat (Steering wheel specification)
7.58. Runningin procedure (1/2)
7.59. Runningin procedure (2/2)
7.60. Greasing (2nd time)
7.61. Touch up work
7.62. On use of starter kit (dummy harness) and precaution on its use
7.63. Starter kit (dummy harness) assembling procedure
7.64. Check inflation pressure of tires
8. Appendix Machine check sheet for field assembly

Rate this product