Yanmar M220-UN to M220L-EX Diesel Engine Operation Manual

Yanmar M220-UN to M220L-EX Diesel Engine Operation Manual - Image 2

Yanmar M220-UN to M220L-EX Diesel Engine Operation Manual - Image 3

Yanmar M220-UN to M220L-EX Diesel Engine Operation Manual - Image 4

Yanmar M220-UN to M220L-EX Diesel Engine Operation Manual - Image 5

yanmar m220 un to m220l ex diesel engine operation manual 2

yanmar m220 un to m220l ex diesel engine operation manual 3

Yanmar M220-UN to M220L-EX Diesel Engine Operation Manual

$20.00

Type Of Manual: Operation Manual
Number of Pages: 307
Size: 11.5MB
Format: PDF

Category: Yanmar Operator Manual PDF

Model List:
- M220-UN, M220-SN, M220-EN, M220L-UN, M220L-SN, M220L-EN, M220AL-UN, M220AL-SN, M220AL-EN, M220L-UX, M220L-SX, M220L-EX Diesel Engine

1. CONTENTS
2. PREFACE
2.1. OUTLINE
2.2. PRECATIONS ON SAFETY
2.2.1. Basic Precation
2.3. PRECATIONS ON OPERATION
2.3.1. Prior to Starting of the Engine
2.3.2. When Starting the Engine
2.3.3. When Stopping the Engine
2.4. PRECATIONS ON MAINTENANCE
2.4.1. Precations Prior to Maintenance Servicing
2.4.2. Precations during Maintenance Servicing
2.4.3. Precations at Coplection of Maintenance Servicing
2.5. LIST OF SAFETY LABELS
3. ENGINE DESCRIPTION
3.1. Marine Main Engine
3.2. Marine Auxiliary Engine/Land Engine
4. ESSENTIAL CHECK POINTS (General Instructions)
5. TABLE OF ENGINE STANDARD ADJUSTMENTS
6. OPERATION
6.1. Operational Preparation
6.2. Starting
6.3. Warming-up
6.4. Initial Running
6.5. Loard Running
6.6. Stopping
6.7. Operation Cutting Off a Fuel Injection Pump
7. FUEL OIL / LUB. OIL COOLIMG WATER
7.1. Fuel Oil
7.2. Lubricating Oil
7.3. Guide for Lub. Oil Changing Time
7.4. Cooling Water
8. PERIODICAL CHECKING
8.1. Perodical Checking (for Normal Service Engine)
8.2. Periodical Checking (for Emergency Engine)
9. DISMAINTLING REASSEMBLING ADJUSTMENT
9.1. Dismaintling Reassembly of Cylinder Head Its Accessories
9.1.1. Cylinder head
9.1.2. Suction exhaust valves
9.1.3. Valve brige its guid
9.1.4. Valve rotator (for suc./exh. valve)
9.1.5. Adjustment of suc./exh. valve head clearance
9.1.6. Fuel injection valve
9.1.7. Starting valve
9.1.8. Control valve
9.2. Removal Reassembly of Piston Connecting Rod
9.2.1. Piston piston pin
9.2.2. Connecting rod
9.2.3. Crank pin metal
9.3. Withedrawal and Replacement of Cylinder Liners
9.3.1. Cylinder block
9.3.2. Cylinder liner
9.4. Disassembly Reassembly of Bed Plate, Main Bearings Crankshaft
9.4.1. Bed plate
9.4.2. Main bearing thrust metal
9.4.3. Crankshaft
9.4.4. Crank deflection measurement
9.4.5. Attaching of front driving coupling
9.4.6. Fitting of front driving coupling oil shield
9.4.7. Disassembly reassembly of the flywheel end crankshaft oil shield part
9.5. Removal and Replacement of Timing Gears, Cam Shaft Suc./Exh. Valve Tappet
9.5.1. Timing gear
9.5.2. Cam shaft
9.5.3. Suc./exh. valve tappet
9.6. Overhaul of Fuel Injection Pump Tappet
9.6.1. Fuel injection pump
9.6.2. Tappet for fuel pump
9.7. Adjustment of Governor Governor Gear
9.7.1. Governor
9.7.2. Governor driving gear
9.7.3. Adjustment of linkage of governor gear
9.8. Dismaitling Reassembling of Lub. Oil Pump, Lub. Oil Cooler
9.8.1. Lub. oil pump (gear type)
9.8.2. Lub. oil cooler
9.8.3. Lub. oil pressure regulating valve
9.9. Overhaul of Cooling Water Pump
9.10. Overhauling of Fuel Feed Pump Rocker Arm Lub. Feed Pump
9.11. Removal Reassembly of Suction Exhaust System
9.11.1. Air duct
9.11.2. Exhaust manifold
9.11.3. Turbocharger
9.11.4. Air cooler (intercooler)
10. PRINCIPAL DIMENSION OF PART MASS FOR DISASSEMBLY SERVICING
10.1. Principal Dimension for Disassembly Servicing
10.2. Principal Parts Mass for Disassembly Servicing
11. TABLE OF TIGHTENING TORUQUES OF MAJOR BOLTS
12. CLEARANCES WEAR LIMITS OF MAJOR PARTS
13. TROUBLE SHOOTINGS COUNTER MEASURES
13.1. Troubleshootings at Starting Time
13.2. Troubleshootings During Operation
14. BOOST AIR TEMPERATURE TWO-STEP CONTROL EQUIPMENT
14.1. Features
14.2. Function and Working of Components
14.3. Handling
14.4. Maintenance Check
14.5. For Your Information
14.6. Fig.1. Inter Cooler Heater
14.7. Fig.2. Air Duct (Inlet)
14.8. Fig.3. Control Equipment
15. PARTS LIST aTTACHED FIGURES
15.1. INDEX FIGURES
15.2. Fig. 1. Outline
15.3. Fig. 2. Sectional View
15.4. Fig. 3-a). Cylinder Head (Marine Diesel Oil Spec.)
15.5. Fig. 3-b). Cylinder Head (Heavy Fuel Oil Spec.) Fuel Injection Valve (Cooling Type)
15.6. Fig. 3-c). Cylinder Head (Heavy Fuel Oil Spec.) Fuel Injection Valve (Non-cooling Type)
15.7. Fig. 4. Valve Rotator
15.8. Fig. 5. Valve Mechanism
15.9. Fig. 6. Camshaft
15.10. Fig. 7. Driving Gear Device Gear Case
15.11. Fig. 8. Cylinder Liner
15.12. Fig. 10. Cylinder Side Cover Relief Valve
15.13. Fig. 11. Main Bearing
15.14. Fig. 12. Main Moving Part Flywheel Side Case
15.15. Fig. 13. Piston Connecting Rod
15.16. Fig. 14-a). Indicator Cock
15.17. Fig. 14-b). Safety Valve
15.18. Fig. 15-a). Fuel Injection Pump (High Pressure Type)
15.19. Fig. 15-b). Fuel Injection Pump (High Pressure Type)
15.20. Fig. 15-c). Fuel Injection Pump Driving Device
15.21. Fig. 16-a). Fuel Injection Valve (Non-Cooling Type) Marine Diesel Oil Spec.
15.22. Fig. 16-b). Fuel Injection Valve (Non-Cooling Type) Heavy Fuel Oil Spec.
15.23. Fig.16-c). Fuel Injection Valve (Cooling Type) Heavy Fuel Oil Spec.
15.24. Fig. 16-d). Fuel Injection Pipe
15.25. Fig. 17-a). Fuel Feed Pump
15.26. Fig. 17-b). Fuel Feed Pump (with Rocker Arm Oil Feed Pump)
15.27. Fig. 17-c). Fuel Feed Pump (with Rocker Arm Lub. Oil pump)
15.28. Fig. 17-d). Fuel Feed Cooling Oil Pump (with Rocker Arm Lub. Oil Pump)
15.29. Fig. 17-e). Fuel Feed Cooling Oil Pump
15.30. Fig. 17-f). Fuel Feed Cooling Oil Common Pump
15.31. Fig. 18-a). Fuel Oil No.1 Filter (25A)
15.32. Fig. 18-b). Fuel Oil No.1 Filter (40A)
15.33. Fig. 18-c). Fuel oil No.1 Filter (50A)
15.34. Fig. 19-a). Fuel Oil No.2 Filter (Notch-wire Type)
15.35. Fig.19-b). Fuel Oil No.2 Filter (Notch-wire Type)
15.36. Fig. 19-c). Fuel Oil No.2 Filter (10μ Heat Insulating)
15.37. Fig. 19-d). Fuel oil No.2 Filter (35μ Steam Jacket)
15.38. Fig. 19-e). Fuel Oil No.2 Filter (35μ Heat Insulating)
15.39. Fig. 20. Lub. Oil Pump
15.40. Fig. 21-a). Suction Side Lub. Oil Strainer (Single Type)
15.41. Fig. 21-b). Suction Side Lub. Oil Strainer (H Type)
15.42. Fig. 22-a). Delivery Side Lub. Oil Strainer (H Type)
15.43. Fig. 22-b). Delivery Side Lub. oil Strainer (Notch-wire Type)
15.44. Fig. 22-c). Pinion Lub. Oil Stariner (Filter Paper Type)
15.45. Fig. 22-d). Indicator for Differentional Pressure
15.46. Fig. 23-a). Lub. Oil Cooler (7.28
15.47. Fig. 23-b). Lub. Oil Cooler7.28
15.48. Fig. 23-c). lub. Oil Cooler (10.3
15.49. Fig. 24-a). Lub. Oil Pressure Regulating Valve (for Main Eng.)
15.50. Fig. 24-b). Lub. Oil Pressure Regulating Valve (for Auxiliary Eng.)
15.51. Fig. 25-a). Lub. Oil Thermostat
15.52. Fig. 25-b). Priming Piston Pump
15.53. Fig. 26-a). Cooling Water Pump
15.54. Fig. 26-b). Cooling Water Pump
15.55. Fig. 27-a). Fuel Oil Pressure Regulating Valve
15.56. Fig. 27-b). Cooling Oil Thermostat
15.57. Fig. 27-c). Accumulator
15.58. Fig. 28. Fuel Injection Valve Leak Pipe
15.59. Fig. 29-a). Rocker Arm Oil Feed Pipe System
15.60. Fig. 29-b). Pinion Feed Oil Pipe System
15.61. Fig. 32-a). Starting Air Distributing Valve
15.62. Fig. 32-b). Control Valve
15.63. Fig. 32-c). Control Valve (Automatic)
15.64. Fig. 33. Starting Valve
15.65. Fig. 34. Starting Air Check Valve
15.66. Fig. 35. Boost Air Pressure Regurating Device (Optional)
15.67. Fig. 36-a). Governor Device
15.68. Fig. 36-b). Governor Driving Device
15.69. Fig. 37-a). Suction Exhaust Pipe System (for Engine Equipped with Turbocharger on the Flywheel Side)
15.70. Fig. 37-b). Suction Exhaust Pipe System (for Engine Equipped with Turbocharger on the Anti-flywheel Side)
15.71. Fig. 38-a). Air Cooler (YPC-28 Type)
15.72. Fig. 28-b). Air Cooler (YPC-40 Type)
15.73. Fig. 39. Starting Air Reservor
15.74. Fig. 40. Semi-automatic Blower Washer
15.75. Fig. 42. Rocker Arm Lub. Oil Tank
15.76. Fig. 40. Steam Trace Pipe System
16. YANMARS WORLDWIDE SERVICE NETWORK

Rate this product