Komatsu D375A-8E0 Bull Dozer Field Assembly Instruction GEN00200-00

Komatsu D375A-8E0 Bull Dozer Field Assembly Instruction GEN00200-00 - Image 2

Komatsu D375A-8E0 Bull Dozer Field Assembly Instruction GEN00200-00 - Image 3

Komatsu D375A-8E0 Bull Dozer Field Assembly Instruction GEN00200-00 - Image 4

Komatsu D375A-8E0 Bull Dozer Field Assembly Instruction GEN00200-00 - Image 5

komatsu d375a 8e0 bull dozer field assembly instruction gen00200 00 2

komatsu d375a 8e0 bull dozer field assembly instruction gen00200 00 3

Komatsu D375A-8E0 Bull Dozer Field Assembly Instruction GEN00200-00

$20.00

Type Of Manual: Field Assembly Instruction
Manual ID: GEN00200-00
Format: PDF
Size: 16.9MB
Number of Pages: 242

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- D375A-8E0 Bull Dozer

1. Cover
2. Preface
3. CONTENTS
4. Specifications
5. Precautions for field assembly
6. Disposal of removed parts
7. Assembly procedure, necessary equipment, and schedule
8. Layout of kit
9. Style for transportation
10. Table of tools for field assembly
11. Tightening torque
12. Coating materials list
13. Selection of wire ropes used for assembly
14. Assembly
14.1. A1 Installation of chassis
14.2. A2 Installation of final drive assy
14.3. A3 Installation of undercarriage
14.4. A4 Adding oil to recoil chamber and pivot chamber
14.5. A5 Installing direction of exhaust pipe
14.6. A6 Installation of blade lift cylinder
14.7. A7 Installation of cylinder yoke grease hose
14.8. A8 Installation of ripper
14.9. A9 Installation of grease hose of ripper pin
14.10. A10 Installation of track
14.11. A11 Assembly of blade
14.12. A12 Installation of blade
14.13. A13 Installation of KOMTRAX antenna
14.14. A14 Installation of ROPS guard
14.15. A15 Installation of platform
14.16. A16 Installation of AUX BOX
14.17. A17 Check track tension
14.18. A18 Check fuel, coolant and lubricants
14.19. A19 Bleeding air from hydraulic cylinders
14.20. A20 Lubricating
14.21. A21 Installation of fuel quick charge piping
14.22. A22 Installation of ladder
15. Check and maintenance procedures after completion of assembly
15.1. M1 Inspection of machine monitor
15.2. M2 Setting procedure for USER ADJUST MODE
15.3. M3 Replacement of return filter
15.4. M4 Flushing of hydraulic circuit, and bleeding air from hydraulic cylinders
15.5. M5 Replacement of return filter
15.6. M6 Bleeding air from hydraulic cylinders
15.7. M7 Method for starting up KOMTRAX terminal and default setting of KOMTRAX Plus controller etc
16. CALIBRATION OF CUTTING EDGE
16.1. Operations and checks after starting engine
16.2. Procedure 1. Adjustment ID 8041 (iB MACHINE SPEC SET MODE)
16.3. Procedure 2. Resetting of cylinder stroke end
16.4. Procedure 3. Adjustment ID 8043 (Adjustment of installed lengths of R.H. and L.H. lift cylinders)
16.5. Procedure 4. Adjustment ID 8044 (L.H. tilt cylinder automatic adjustment)
16.6. Procedure 5. Adjustment ID 8048 (AUTO PITCH ADJUST)
16.7. Procedure 6. Adjustment ID 8040 (CYLINDER CALIBRATION MODE)
16.8. Procedure 7. Adjustment ID 8042 (iB W/E VALVE AUTO SET MODE)
16.9. Procedure 8. Inputting wear amount of blade edge and track shoe
16.10. Procedure 9. 10. Special functions of control box
16.11. Procedure 9. Operation of Machine Cal Step A menu
16.12. Procedure 10. Operation of Machine Cal Step B menu
16.13. Procedure 11. Checking and adjusting blade edge elevation
17. Field assembly inspection report

Rate this product