komatsu wa430 6 wheel loader operation and maintenance manual veam350100 1 1

komatsu wa430 6 wheel loader operation and maintenance manual veam350100 2 2

komatsu wa430 6 wheel loader operation and maintenance manual veam350100 3

komatsu wa430 6 wheel loader operation and maintenance manual veam350100 4

komatsu wa430 6 wheel loader operation and maintenance manual veam350100 5

Komatsu WA430-6 Wheel Loader Operation and Maintenance Manual VEAM350100

$20.00

Type Of Manual: Operation and Maintenance Manual
Manual ID: VEAM350100
Format: PDF
Size: 9.8MB
Number of Pages: 337

Category: Komatsu Operation and Maintenance Manual PDF

Model List:
- WA430-6 Wheel Loader

1. VEAM350100_WA4306OMM
2. Foreword
2.1. Foreword
2.1.1. EU Directives
2.2. Safety information
2.2.1. Signal words
2.2.2. Safety labels
2.3. Introduction
2.3.1. Intended use
2.3.2. Directions of machine
2.4. Necessary information
2.4.1. Machine serial no. plate and position
2.4.2. Engine serial no. plate and position
2.4.3. ROPS/FOPSCab serial no. plate
2.4.4. Axle serial no. plate
2.4.5. Transmission serial no. plate
2.4.6. Seat operator serial no. plate
2.4.7. Position of service meter
2.4.8. Table to enter serial no. and distributor
2.5. Contents
2.6. Dimensions, weights and operating data
2.6.1. WA4306 Dimensions, weights and operating data
2.7. CEConforming equipment
2.7.1. CEConforming equipment
2.7.2. Manufacturersupplied CEConforming equipment, according to document 42193H1900
3. Safety
3.1. Safety labels
3.1.1. Location of safety labels
3.1.2. Presentation of safety labels
3.2. General precautions
3.3. Precautions for operation
3.3.1. Starting engine
3.3.2. Operation
3.3.3. Transportation
3.3.4. Battery
3.3.5. Towing
3.4. Precautions for maintenance
3.5. Precautions with tires
4. Operation
4.1. General view
4.1.1. General view of machine
4.1.2. General view of controls and gauges
4.2. Explanation of components
4.2.1. Machine monitor
4.2.2. Switches
4.2.3. Control levers, pedals
4.2.4. Steering tilt lock lever
4.2.5. Cap with lock
4.2.6. Safety bar
4.2.7. Towing pin
4.2.8. Grease pump
4.2.9. Cab door open lock
4.2.10. Cab window open lock cancel knob
4.2.11. Backup alarm
4.2.12. Fuse
4.2.13. Slow blow fuse
4.2.14. Power outlet
4.2.15. Air conditioner
4.2.16. Cool box
4.2.17. Handling cab wiper
4.3. Operation
4.3.1. Check before starting engine, adjust
4.3.2. Starting engine
4.3.3. Operations and checks after starting engine
4.3.4. Stopping engine
4.3.5. Moving the machine (directional, speed), stopping the machine
4.3.6. Turning
4.3.7. Operation of work equipment
4.3.8. Work possible using wheel loader
4.3.9. Precautions for operation
4.3.10. Adjusting work equipment posture
4.3.11. Parking machine
4.3.12. Check after stopping engine
4.3.13. Checks after completion of operation
4.3.14. Locking
4.3.15. Handling the tires
4.4. Transportation
4.4.1. Transportation procedure
4.4.2. Loading, unloading work with trailers
4.4.3. Lifting machine
4.5. Cold weather operation
4.5.1. Precautions for low temperature
4.5.2. Precautions after completion of work
4.5.3. After cold weather
4.5.4. Warmingup operation for steering hydraulic circuit in cold weather
4.6. Longterm storage
4.6.1. Before storage
4.6.2. During storage
4.6.3. After storage
4.7. Troubleshooting
4.7.1. When machine runs out of fuel
4.7.2. Towing the machine
4.7.3. If battery is discharged
4.7.4. Other trouble
5. Maintenance
5.1. Guides to maintenance
5.2. Outlines of service
5.2.1. Handling oil, fuel, coolant, grease and carrying out KOWA (KOMATSU Oil Wear Analysis)
5.2.2. Outline of electric system
5.3. Wear parts
5.3.1. Wear parts list
5.4. Fuel, coolant and lubricants
5.4.1. Lubrication chart
5.4.2. Proper selection of fuel, coolant and lubricants
5.4.3. Recommended brands, recommended quality for products other than Komatsu genuine oil
5.5. Standard tightening torques for bolts and nuts
5.5.1. Torque list
5.6. Periodic replacement of safety critical parts
5.7. Maintenance schedule chart
5.7.1. Maintenance schedule chart
5.8. Adjust injector
5.8.1. A Regulation area
5.8.2. B Regulation area
5.9. Service procedure
5.9.1. Initial 250 hours service (only after the first 250 hours)
5.9.2. Initial 1000 hours service (only after the first 1000 hours)
5.9.3. When required
5.9.4. Check before starting
5.9.5. Every 50 hours service
5.9.6. Every 100 hours service
5.9.7. Every 250 hours service
5.9.8. Every 500 hours service
5.9.9. Every 1000 hours service
5.9.10. Every 2000 hours service
5.9.11. Every 4000 hours service
5.9.12. Every 8000 hours service
6. Technical Data
6.1. Technical data
6.2. Noise emission levels
6.3. Vibration level
6.4. Limit values for slopes
7. Attachments, Options
7.1. Selecting bucket and tires
7.2. Joystick steering system
7.2.1. Components
7.2.2. Structure and function
7.2.3. Operation method of joystick steering system
7.3. EPC work equipment lever
7.3.1. Operational features
7.3.2. Switches
7.3.3. Semi auto digging operations
7.4. Multifunction lever
7.4.1. Explanation of components
7.4.2. Operation
7.5. Central lubrication system
7.5.1. Operating the central lubrication system
7.5.2. Display and control unit
7.5.3. Changing the lubrication interval times
8. Index
8.1. Index
9. Notes

Rate this product